How To Remove Rear Door Panel 1992-96 Toyota Camry
Created on: 2011-01-12
Watch this video to learn how to remove the rear door panel on your 92-96 Toyota Camry. 1A Auto shows you how to do it yourself!
-
step 1 :Remove the door panel
- Pry up the door handle bezel with your flat blade screwdriver.
- Pull up the switch panel from the door pull.
- Disconnect the wiring harness.
- Remove the Phillips screws tucked up under the door pull.
- On the sides of the door panel, there will be push clips.
- Depress the center to unlock the body and remove the pin.
- With a putty knife, unclip the door panel from the door.
-
step 2 :install the door panel
- Thread the wiring harness through the door pull.
- Line the door panel up and firmly push the door panel pins into the door.
- Replace the push clips into the side of the door.
- Use your Phillips screwdriver to replace the two screws under the door pull.
- Connect your switch panel and clip it into the door pull.
- Replace the door handle bezel.
Tools needed
-
Flat Blade Screwdriver
Phillips Head Screwdriver
Putty Knife
Door Panel Removal Tool
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my twenty plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly, that's going to save you time and money. Thank you, and enjoy the video.
In this video, we show you how to remove and install the rear door panel on this '94 Camry, same as any '92-'96. The only tools you'll need are a flat blade screwdriver and a Phillips screwdriver and a putty knife or door panel clip tool. Start out using a flat blade screwdriver. Push it up in there and pull that out and down in here. They're going a little further on the bottom, and then that pops off. Power window switch from under in the front and then slide up and out, and then there's a little button right here you press with your thumb, disconnect that.
OK, and then there's a little plug here that covers a Phillips screw, and that Phillips screwdriver, and another Phillips screw right under here. Kind of put your screwdriver up in there, feel around a little bit till you get it. OK, and then on the back of the door you have little pins here. Push the center in. Another one down here, push the center in, and then, either using a screwdriver or your fingernails, just pry those out. There are two more of those on the front, one up here, and one here. OK, and then one of the best things is use a putty knife. Stick it in, slide it until you hit something, pull out, and there's three clips, and lift your door panel up and off. OK, Re-install your door panel. Make sure you feed your harness up through. OK, go up a little higher, push the top of the panel against the window, and then down.
I like to put my switch on right away just so this harness doesn't try and slide down and get lost down there. Put that in, push it down in. Push the back down first and the front clips. OK, clip the bottom. Reset your little clips by pushing them up like that, and then start down. Insert then lock. This screw just kind of stayed in there. Should be kind of an up angle to get it where it wants to go, and tighten it up nice and firm. OK, then this has a little tab in it that goes into a slot so you know you're putting it in at the right angle, and then you want, there's a tab at the front of this that you want to lock into here, so you want to put, kind of angle the front first, and you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel to call us toll-free, 888-844-3393. We're the company that serves you on the internet and in person.
