Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Remove Horns 09-19 Ford Fiesta

Share on:

How to Remove Horns 09-19 Ford Fiesta

Created on: 2019-03-15

How to replace a shorted or muffled horn on 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19 Ford Fiesta

  1. step 1 :Removing the Passenger Side Headlight
    • Remove the three T30 bolts from the headlight
    • Pry up the body clip from the headlight
    • Grab and firmly pull the headlight up from the center and toward the windshield
    • Disconnect the two metal tabs and four electrical connectors from the headlight
    • Remove the headlight
  2. step 2 :Removing the Horn
    • Remove the 8mm mounting bolt from the horn
    • Lift the horn up
    • Disconnect the wiring harness from the horn
  3. step 3 :Installing the Horn
    • Connect the wiring harness
    • Insert the horn into place
    • Tighten the 8mm mounting bolt to the horn
  4. step 4 :Installing the Passenger Side Headlight
    • Place the plastic guide on the bottom of the headlight into the lip of the bumper
    • Connect the four electrical connectors and the two metal clips
    • Clip in the body clip to the headlight
    • Tighten the three T30 bolts to the headlight

Tools needed for replacement

  • Materials, Fluids, and Supplies

    Rust Penetrant

  • Ratchets & Related

    Socket Extensions

    Ratchet

  • Screwdrivers & Related

    Flat Blade Screwdriver

  • Sockets - Metric

    8mm Socket

  • Specialty Tools

    Trim Tool Set

  • Star Drivers & Sockets

    T30 Driver

Installation Video
Watch video

Hi I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.

Hey, everyone. Sue here from 1A Auto and now we have a 2011 Ford Fiesta in the shop, and I'm going to show you the location of the horn assembly and how to get to it.

So we're going to start off with opening the hood. We raise the hood up, and the horn assembly is on the passenger side, and it's underneath the actual headlamp assembly. So you have to remove the headlamp. So what you're going to need is a T30 Torx and a body clip tool to remove those, just one clip.

So, we'll start with the body clip tool. Slide it up underneath and pull that tab out. And pull the base of it out. Set that aside, and we're going to grab your T30 and remove the three mounting bolts locations. Seems like the hood rod is just a little bit in the way, but we're going to work around it easily. And we are going to take the headlamp assembly out, so you're going to disconnect the electrical connectors. So with a firm handle I'm going to grab up the back here and pull this tab right out. And now it's going to slide this way just a hair. I'm going to disconnect this electrical connector and then the harness, that connector. Now we can pull that right up. Set that aside.

And there's the horn assembly right here. It's got an 8mm mounting bolt and the electrical connector down here. So I'm going to spray that mounting bolt. Get a socket. With an 8mm socket, I'm going to put right on the head of that bolt and break her free.

Now we can see the electrical connector a little bit better. Lift it up and work with it easier. Now there's the tab. I'm going to push down that tab and release the harness. Now to reinstall you're going to reverse procedure. If you were to buy a horn, if you didn't get the factory horn and you got a universal horn, it's going to come with its own bracket and new connectors to splice into the horn assembly. It's basically a two-wire, so if it doesn't have it so that you can adapt the old connector factory style, then you're going to splice your wires and put them on the spades.

Reconnect. This has that mounting tab on it. Put the bolt in. Get your socket. Tighten it up. It just has to be hand-tight. You don't have to torque it or anything. Now we can reassemble our lamp assembly. Make sure you guide the plastic into the bumper cover. Line that up. I'm going to put the electrical connectors before I slant the assembly down in. Hear it click into place.

Pretty much falls right down into place. I'm going to put that plastic tab back in first. And I've got three mounting torque head bolts. Start them by hand. Make sure they're all lined up properly. And then I'll take my T30. Snug them down. Here we go.

Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping and the best customer service in the industry.

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket

  • Specialty Tools

  • Trim Tool Set

  • Star Drivers & Sockets

  • T30 Driver


Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Loading...