Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Includes:   with Washer Pump

Our aftermarket reservoirs are some of the highest quality replacements on the market!

This Nissan Maxima Windshield Washer Reservoir is a complete, ready to bolt on, direct replacement part.


  • Includes washer pump
  • Has provision for low fluid sensor
  • Brand new in the box!
  • High quality item that is built to strict quality control standards
  • Direct bolt on
  • Does not include cap

Assembly replaces the following dealer part numbers:

  • 2891785E00, 2891040U00, 28910-40U00, 289111E400, 28911-1E400, 2891331U00, 28913-31U00, 2891340F00, 28913-40F00, 2891531U00, 28915-31U00, 2891540U00, 28915-40U00, 2891541U00, 28915-41U00, 2891543U00, 28915-43U00, 2891770F00, 28917-70F00, 28917-85E00, 289201E400, 28920-1E400, 2892150Y00, 28921-50Y00

Now you can buy a high quality reservoir that is built to strict quality control standards. This makes a great replacement and has great cost savings over a factory assembly.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Front Bumper Cover (0:42)
    • Pry up the four bumper clips 1/8 inch with a flat blade screwdriver
    • Pull out the four bumper clips
    • Remove the two Phillips head screws from beneath the bumper cover
    • Pry up and remove the clips underneath the bumper cover
    • Pull back the inner fenders
    • Remove the first 10mm bolt inside each wheel well
    • Wrap a flat blade screwdriver with a rag to avoid chipping your paint
    • Pry out the side marker lights
    • Remove the second 10mm bolt inside each wheel well
    • Pull the bumper cover forward
    • Disconnect the fog light wiring harnesses
    • Pull the bumper cover off
  2. step : Removing the Windshield Washer Fluid Bottle (4:35)
    • Have a drain pan ready
    • Disconnect the washer pump wiring connector
    • Lock the washer pump line
    • Pull the pump off
    • Allow the washer fluid to drain
    • Open the washer fluid bottle cap to allow the fluid to drain more quickly
    • Remove the washer fluid pump lines from the fluid bottle clips
    • Pull out the washer fluid bottle fill tube
    • Remove the three 10mm bolts from the washer bottle
    • Pull the washer bottle out
    • Disconnect the fluid level sensor with a flat blade screwdriver
  3. step : Installing the New Windshield Washer Fluid Bottle (7:55)
    • Put the washer bottle into place
    • Hang the washer bottle from its bracket
    • Insert the three 10mm bolts into the washer bottle
    • Connect the fluid level sensor to the washer bottle
    • Connect the fluid pump to the washer bottle
    • Push the washer pump hoses onto their clips
    • Push the washer fluid fill neck into place
  4. step : Refilling the Windshield Washer Fluid (10:04)
    • Fill the washer fluid bottle using a funnel
    • Put on the washer fluid fill neck cap
  5. step : Testing the Windshield Washers (10:25)
    • Turn the vehicle's ignition on
    • Run the windshield washers
    • Check that they are working
    • Turn the ignition off
  6. step : Reinstalling the Front Bumper Cover (10:47)
    • Lift the bumper cover into place
    • Connect the fog light wiring harnesses
    • Apply penetrating oil to the bumper clips and clean them
    • Insert the clips into the top of the bumper cover
    • Insert the 10mm bolts in the wheel well
    • Push the side marker lights into place
    • Push the inner fenders behind the bumper cover lip
    • Push the splash shield over the bumper cover
    • Insert the clips underneath the bumper cover
    • Insert the Phillips screws underneath the bumper cover

Tools needed for replacement:

    General Tools

  • Drain Pan
  • Funnel

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

2.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Couldnt use reservoir
It was guaranteed to fit, but there was a manufactured hole apx one inch diameter in the reservoir bottom.... there was no plug included for it. therefore couldnt use the reservoir as of course nothing could be reservoired in it. Used the pump only that was included and that worked for me so it wasnt a complete fail on the guaranteed fit.
August 23, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
There is only one review of this product and they said it doesnt fit? Has the problem been corrected. I would be buying this for a 2000 Maxima SE 5-spd
Lonnie M October 23, 2018
This should be able to fit correctly for your vehicle.
Emma F October 23, 2018
Year Make Model Description
1996-2001Infiniti I30 Infiniti I30 with Low Fluid Sensor Windshield Washer Reservoir with Washer Pump
2002-2004Infiniti I35 Infiniti I35 with Low Fluid Sensor Windshield Washer Reservoir with Washer Pump
1994-2003Nissan Maxima Nissan Maxima with Low Fluid Sensor Windshield Washer Reservoir with Washer Pump
Part #: 1AWWR00001

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(12:47 min)