Part Details

  • Regulator Option: without Motor
  • Operation: Power

This window regulator is just what you need to get your vehicle in good working form again!

Specifications:

  • RH (Passenger Side) REAR
  • Power operation
  • Replaces dealer part numbers: XW7Z-5427008-AA, 6W7Z-5427008, XW7Z5427008AA, 6W7Z5427008
  • Does NOT include power window motor
  • Direct replacement
  • Built to strict quality control standards

This window regulator is a great replacement that offers good cost savings over the dealer part!

Please Note:

This window regulator is designed to work with factory style motors only.  Due to variations in aftermarket designs, replacement motors may not have the correct gear style.

Please Note:

This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. It has been subjected to extensive testing and quality control standards. That is why we offer this regulator with our superior warranty!

Rigorously Tested

Build to strict quality standards

Highest Quality Materials

Made from the highest quality materials for extreme durability and premium performance.

Item Condition: New

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (1:03)
    • Pry up the switch panel with a flat blade screwdriver
    • Remove the Phillips head screws from the window switch harness
    • Pry out on the switch with a flat blade screwdriver
    • Pry off the bezel with a flat blade screwdriver
    • Pry off the two trim covers on the pull handle
    • Remove the two Phillips screws from the pull handle
    • Remove the Phillips screw from behind the switch panel
    • Remove the Phillips screw on the bottom of the door panel
    • Lift the panel up and off
    • Carefully pull off the water shield
  2. step : Removing the Rear Inside Door Handle (3:07)
    • Remove the Phillips screw from the door handle
    • Slide the handle forward and pull it out
    • Remove the door handle rod from the inside door handle
  3. step : Removing the Window Regulator (3:32)
    • Punch out the center of the rivets on the window motor with a hammer and punch
    • Punch out the rivets on the regulator
    • Punch out the rivets on the window
    • Drill out the rivets with a 3/8 bit
    • Remove the two 11mm bolts from the bottom of the regulator
    • Lower the window
    • Pull off the weatherstrip and trim around the window frame
    • Lift the secondary window up and out
    • Push the secondary window down and its weather strip down from the window frame
    • Raise the window by hand
    • Remove the window
    • Remove the two 11mm nuts on the top of the door
    • Disconnect the window motor lead
    • Pull the window regulator out through the door
  4. step : Reinstalling the Regulator (11:25)
    • Insert one of the bolts into the window regulator
    • Push the regulator into the door
    • Hang the regulator by the 11mm bolts in the regulator rail
    • Insert the two bolts into the window track
    • Insert the three bolts to the motor
    • Pry off the old rivets from the window with a flat blade screwdriver
    • Lower the window onto the regulator
    • Insert the two bolts into the bottom of the regulator
    • Lower the secondary window into place
    • Lift the window into place
    • Insert the two bolts that hold the window to the regulator
    • Put the weatherstrip and trim into place
  5. step : Installing the Rear Inside Door Handle (17:08)
    • Insert the door handle rod to the inside door handle
    • Slide the door handle back
    • Tighten the Phillips screw to the door handle
  6. step : Reinstalling the Door Panel (17:23)
    • Put the water shield in place
    • Lift the door panel into place
    • Insert the longer Phillips screw behind the switch panel
    • Insert the longer Phillips screw to the bottom of the door panel
    • Insert the two Phillips screws to the pull handle
    • Push the switch into the switch panel
    • Push the switch panel in place
    • Push in the door handle bezel
    • Push in the trim buttons on the pull handle

Tools needed for replacement:

    Drills, Drill Bits & Related

  • 3/8 Inch Drill Bit
  • Drill

  • Materials, Fluids, and Supplies

  • Coarse Threaded Bolts (to replace rivets)

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 11mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1992-2011Ford Crown Victoria Ford Crown Victoria Rear Power Window Regulator without Motor Passenger Side
1992-2010Mercury Grand Marquis Mercury Grand Marquis Rear Power Window Regulator without Motor Passenger Side
2003-2004Mercury Marauder Mercury Marauder Rear Power Window Regulator without Motor Passenger Side

This part replaces:

  • Partslink FO1551102
  • Hollander 135-1829A, B
  • Dorman 740-678
  • OE # XW7Z5427008AA
Part #: 1AWRG00128


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(19:34 min)