Part Details

  • Bearing Type: Ball Bearing
  • Quantity: 4 Piece Set

Specifications:

  • Brand New CV Axle & Wheel Bearing Kit
  • Comes as a 4 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards
Precision Engineered

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.
100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:03)
    • While your car is still on the ground, use your 32mm socket to loosen the center hub nut
    • Loosen your lug nuts and jack up the car
    • Remove the lug nuts with your 19mm socket and ratchet
    • Remove the wheel and set aside
  2. step : Removing the Brakes (2:23)
    • Remove the 13 and 15mm bolts holding the calipers and the bracket
    • Wire tie the caliper up and out of the way, set the bracket to the side
    • Remove your rotor and set aside
    • Remove your dust shield by removing the 3 8mm bolts
    • Disconnect your ABS wiring harness using a 5mm allen wrench
  3. step : Removing the Hub (4:00)
    • Use an axle puller or a light but firm tap with a small hammer on the axle to remove the hub
    • Remove the 3 15mm bolts, using penetrating oil to help
    • A breaker bar or piece of pipe on the end of your ratchet may be needed
    • Remove the hub and clean the area with a wire brush
  4. step : Replacing the Hub (8:55)
    • Put position your new 1A Auto hub on the axle
    • Put the three 15mm bolts in place and tighten the nuts to 70 ft lbs
    • Reinstall your wiring harness, clip everything to the frame
    • Reinstall your dust shield, tightening the three 8mm bolts up
  5. step : Reinstalling the Brakes and Wheel (10:40)
    • Refer to our other videos for more detailed instructions
    • Remember to replace the lug nuts on in a star pattern
    • Lug nuts tighten to 90-100 ft lbs
    • Hub nut is 157-213 ft lbs
    • Make sure to check your brakes and steering before driving again
    • Make sure to have the vehicle aligned

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 15mm Socket
  • 19mm Socket
  • 8mm Socket
  • 13mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1995-2001Ford Explorer Ford Explorer 4 Wheel Drive 4 Piece Set Front Wheel Hub Bearing & Axle Kit
2001-2002Ford Explorer Sport Trac Ford Explorer Sport Trac 4 Wheel Drive 4 Piece Set Front Wheel Hub Bearing & Axle Kit
1997-2001Mercury Mountaineer Mercury Mountaineer 4 Wheel Drive 4 Piece Set Front Wheel Hub Bearing & Axle Kit

This part replaces:

  • A1 Cardone 66-2101
  • A1 Cardone 66-2027
  • Reference Number 515003
  • OE # F87Z1104CA
Part #: 1AHTF00023

Out of Stock

How-to Video:

(12:15 min)