Replaces

Wheel Bearing & Hub Assembly TRQ BHA84970 - 1ASHS01172

Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (0:49)
    • Remove the hub cap
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the lug nuts and set the wheel aside.
    • Turn the wheels for easier access to the calipers.
  2. step : Remove the brakes (1:06)
    • Remove the two 12mm bolts with a socket and breaker bar.
    • Use a C-Clamp to compress the caliper piston.
    • Pull the caliper off.
    • Remove the brake pads and check the life of them.
    • Observe the rotors; prepare a new rotor with brake cleaner if it is in need of replacement.
    • Use a 13mm socket and breaker bar to remove the caliper bracket bolts.
    • Remove the rotor.
  3. step : Remove the hub (3:42)
    • Disconnect the ABS sensor.
    • Remove the 35mm socket to remove the hub nut.
    • Put the wheel back on and lower the car to break the hub nut loose if necessary.
    • Use a 13mm socket and breaker bar to loosen the three nuts on the back side securing the hub.
    • Put an axle puller onto the hub and axle to break the axle free from the hub.
    • Sometimes a solid thwack with a hammer is enough to break the axle loose, taking care not to hit it hard enough to damage the CV joint.
    • Remove the 13mm nuts all the way and pull the hub off.
  4. step : install the new hub (6:48)
    • Thread the ABS harness through and line the axle up into the center of the hub.
    • Evenly tighten the three 13 mm bolts.
    • Connect the ABS sensor harness.
    • Torque the 13mm bolts to 65 ft lbs
    • Put the hub nut on, put the wheel on, lower the car, and torque it to 173 foot pounds.
    • Raise and secure the car, remove the wheel and continue.
  5. step : Put the brakes on (8:28)
    • Put your rotor on the hub.
    • Mount the caliper bracket and torque the 15 mm bolts to 65 ft lbs.
    • Install the brake pads.
    • Dab a little anti-seize grease onto the edges of the brake pads and insert them into the brackets
    • Install the caliper, and torque the caliper bolts to 15-18 ft lbs.
  6. step : put the wheel back on (11:00)
    • Put the wheel on and hand tighten the lug nuts.
    • Lower the vehicle and torque the lug nuts to 90-100 ft-lbs in a star pattern.
    • Pump your brakes and do a couple test stops before driving your car anywhere.

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Wire Brush

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 12mm Socket
  • 13mm Socket
  • 19mm Socket
  • 35mm Socket

  • Specialty Tools

  • Pitman Arm Puller

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2005 Chevy Classic Front Wheel Bearing & Hub Assembly for Models with ABS Brakes with (1) 36mm Axle Nut Socket TRQ
  • 1997-2003 Chevy Malibu Front Wheel Bearing & Hub Assembly for Models with ABS Brakes with (1) 36mm Axle Nut Socket TRQ
  • 1999-2004 Olds Alero Front Wheel Bearing & Hub Assembly with (1) 36mm Axle Nut Socket TRQ
  • 1997-1999 Olds Cutlass Front Wheel Bearing & Hub Assembly (excluding Supreme Models) with (1) 36mm Axle Nut Socket TRQ
  • 1999-2005 Pontiac Grand Am Front Wheel Bearing & Hub Assembly with (1) 36mm Axle Nut Socket TRQ

This part replaces:

  • TRQ BHA84970
Part #: 1ASHS01172

Out of Stock

TRQ
Brand #: BHA84970

How-to Video:

(12:41 min)