Replaces

Wheel Bearing & Hub Assembly TRQ BHA84977 - 1ASHS01181

Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Step 1: Remove the wheel and tire (1:18)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Step 2: Remove Caliper (2:07)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 13mm socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your 18mm socket to remove the brackets.
  3. step : Step 3: Remove brake disk (4:13)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Step 4: Remove Hub (4:42)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. step : Step 5: Install new hub (9:10)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 90 ft lbs.
    • Reinstall the ABS harness.
    • Tighten but don't torque the lug nut.
  6. step : Step 6: Put brakes and wheel back on (11:50)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 100-120 ft lbs
    • Hub nut is 103 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Rubber Mallet
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 19mm Socket
  • 35mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Seems like a quality part
The installation was fairly simple in terms of what to do, not much harder than changing brakes. All bolts came off easy enough with letting some penetrating spray work for 15-20 minutes and a breaker bar. It took a bit more hammering to get the hub off the spline than in the video. Part seems quality, and a slight vibration is now gone. It remains to be seen if the ABS light that used to come in in very cold weather continues or not, but I'm guessing it won't. If you are somewhat handy, expect to spend 2.5 to 3 hours.

1A Auto should include a 6 point socket instead of a 12 point.
January 17, 2018
Purchased
5 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2007 Buick Rainier Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2003-2006 Chevy SSR Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2002-2009 Chevy Trailblazer Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2002-2006 Chevy Trailblazer EXT Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2002-2009 GMC Envoy Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2002-2006 GMC Envoy XL Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2004-2005 GMC Envoy XUV Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2003-2008 Isuzu Ascender Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2002-2004 Olds Bravada Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ
  • 2005-2009 Saab 9-7X Front Wheel Bearing & Hub Assembly Driver or Passenger Side with (1) 36mm Axle Nut Socket TRQ

This part replaces:

  • TRQ BHA84977
Part #: 1ASHS01181


TRQ
Brand #: BHA84977

How-to Video:

(13:45 min)