Wheel Bearing & Hub Assembly TRQ BHA54211 - 1ASHR00074


  • Fits either LH (Driver Side) or RH (Passenger Side) REAR
  • 4 Bolt Rectangular Flange
  • Fits 5 Lug Wheel
  • Studs already installed
  • Built to strict quality control standards
  • Fits models with ABS - RPO Code "JL9"
  • Has ABS sensor built in with correct plug configuration
  • Fits FWD (Front Wheel Drive) Models only


  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.


  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.
Precision Engineered

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application.

Part Details

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:59)
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the center cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:23)
    • Remove the two 14mm bolts from the brake caliper
    • Pull the caliper aside
    • Pull the brake pads off
  3. step : Removing the Brake Rotor (2:04)
    • Remove the two 13mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Hold the rotor in place with a flat blade screwdriver
    • Remove the T30 Torx screw from the rotor
    • Strike the rotor with a hammer to loosen it
    • Pull the rotor off
  4. step : Removing the Wheel Hub (3:16)
    • Remove the four 10mm bolts from the wheel hub
    • Disconnect the ABS wiring harness from the hub
    • Strike the hub with a hammer to remove it
    • Push out the emergency brake cable pin with a hammer and a screwdriver
    • Pull the spring off the brake backing plate with a screwdriver
    • Pull the emergency brake cable out of the brake backing plate
  5. step : Separating the Wheel Hub from the Brake Backing Plate (5:01)
    • Remove the two T30 screws from the backing plate
    • Pull the bracket off of the backing plate
    • Pull the backing plate off of the hub
    • Pull the emergency brake ring off of the hub
  6. step : Preparing the New Wheel Hub (5:35)
    • Clean the hub mounting area with a wire brush
    • Apply white grease or bearing grease to the mounting area
    • Put the emergency brake ring onto the backing plate
    • Put the hub through the ring and backing plate, making sure the ABS wiring connector is lined up with the backing plate hole
    • Pull the arm off the emergency brake activator
    • Put the emergency brake activator onto the ring
    • Attach the bracket to the backing plate
    • Insert the two T30 screws into the bracket
    • Push the emergency brake arm into place through the bracket
  7. step : Installing the New Wheel Hub (7:39)
    • Attach the emergency brake cable to the emergency brake arm
    • Push the emergency brake cable into its bracket
    • Insert the pin into the bracket, using a hammer
    • Attach the spring to the emergency brake arm
    • Pull the spring onto the bracket with vise-grip pliers
    • Push the hub into place
    • Start one of the 10mm bolts to hold the hub in place
    • Start the remaining three 10mm bolts
    • Tighten the four 10mm bolts to 45 - 50 foot-pounds of torque
    • Reconnect the ABS wiring harness
    • Adjust the emergency brake, by turning the wheel with a flat blade screwdriver
  8. step : Reinstalling the Brake Rotor (9:43)
    • Slide the rotor on
    • Adjust the emergency brake further, if necessary
    • Insert the T30 screw into the rotor
    • Put the bracket back into place
    • Start the two 13mm bolts by hand
    • Tighten the bolts to 75 foot-pounds of torque
  9. step : Reinstalling the Brake Pads (10:45)
    • Apply grease to the brake pads
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten bolts to 30 foot-pounds
  10. step : Reattaching the Wheel (11:27)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 14mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
The howling noise went away. Was easy to install,
Fit like a glove.
I'll need to purchase the other side soon.
August 19, 2017
11 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 4 answers
Emergency brake assembly on passenger side rear as well?
X x on Apr 11, 2016
BEST ANSWER: Yes there is one on each rear. Just remove the screw and you can pull the outer portion off to allow the rest to be worked on.
What size lug stud do I need that fits a 2008 chevy impala SS?
Prentice B on Feb 11, 2017
BEST ANSWER: We are unable to provide the exact wheel lug stud size. We recommend contacting a dealership with your VIN number to obtain this information as our parts are built to the same OE specifications.
this part fit fwd only?
edward w on Dec 7, 2015
BEST ANSWER: Hello and thank you for your inquiry. Yes, this will only fit the FWD vehicles. Thank you and have a great day.

Vehicle Fit

  • 2005-2008 Buick Allure with ABS Brakes Rear Wheel Bearing & Hub Assembly TRQ
  • 2009 Buick Allure Rear Wheel Bearing & Hub Assembly TRQ
  • 2005-2008 Buick LaCrosse with ABS Brakes Rear Wheel Bearing & Hub Assembly TRQ
  • 2009 Buick LaCrosse Rear Wheel Bearing & Hub Assembly TRQ
  • 2005 Buick Terraza Front Wheel Drive 4 Bolt Flange Rear Wheel Bearing & Hub Assembly TRQ
  • 2006-2008 Chevy Impala with ABS Brakes Rear Wheel Bearing & Hub Assembly TRQ
  • 2009-2013 Chevy Impala Rear Wheel Bearing & Hub Assembly TRQ
  • 2014-2016 Chevy Impala Limited Rear Wheel Bearing & Hub Assembly TRQ
  • 2006-2007 Chevy Monte Carlo with ABS Brakes Rear Wheel Bearing & Hub Assembly TRQ
  • 2005 Chevy Uplander Front Wheel Drive 4 Bolt Flange Rear Wheel Bearing & Hub Assembly TRQ
  • 2004-2008 Pontiac Grand Prix with ABS Brakes Rear Wheel Bearing & Hub Assembly TRQ
  • 2005 Pontiac Montana SV6 Front Wheel Drive 4 Bolt Flange Rear Wheel Bearing & Hub Assembly TRQ
  • 2005 Saturn Relay Front Wheel Drive 4 Bolt Flange Rear Wheel Bearing & Hub Assembly TRQ

This part replaces:

  • OE # 12403095
  • OE # 88964177
  • Hollander 538-01635
  • TRQ BHA54211
Part #: 1ASHR00074

Brand #: BHA54211

How-to Video:

(12:19 min)