Replaces

Wheel Bearing & Hub Assembly TRQ BHA54205 - 1ASHR00063

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
    Direct Fit Replacement
    Precision Engineered
    Highest Quality Materials
  • Bearing Type: Ball Bearing

This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Fits RH (Passenger Side) REAR
  • Replaces dealer part numbers: 42450-06020, 42450-06021, 42450-06030, 42450-48010, 42450-48011, 4245006020, 4245006021, 4245006030, 4245048010, 4245048011
  • Studs already installed
  • Direct replacement
  • Built to strict quality control standards
This wheel bearing & hub assembly is a great replacement and has good cost savings over a unit from the dealer.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:25)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads and Rotor (1:05)
    • Remove the two 14mm bolts from the caliper
    • Secure the caliper out of the way with a bungee cord
    • Pop the brake pad out of the caliper bracket
    • Remove the 14mm caliper bracket bolts
    • Remove the caliper bracket
    • Pry out the rubber plug from the rotor
    • If the rotor is stuck, tap around the drunk with a dead blow hammer
    • Tap the adjustor down
    • Remove the rotor
  3. step : Removing the Hub Assembly (5:08)
    • Disconnect the ABS sensor wiring harness from behind the hub
    • Insert a 17mm socket, socket extension, and ratchet into the slots on the hub
    • Remove the bolts
  4. step : Ways to Remove a Stuck Hub (7:00)
    • Tap around the hub's edges with a dead blow hammer to loosen it
    • Place a rotor on backwards
    • Thread a few lug nuts on
    • Tap the rotor with a dead blow mallet
    • If the backing plate comes off with the hub assembly, spray rust penetrant in the seams
  5. step : Removing the Brake Shoes (9:48)
    • Remove the brake shoe springs with the vise grip pliers
    • Remove the brake adjuster
    • Remove the upper adjustor piece and spring
    • Twist the nail and remove the retainer, spring, and nail from the brake shoe
    • Remove the brake shoes
    • Remove the cable from the brake shoe arm
    • Remove the 10mm bolt from the backing plate
    • Pull the e-brake cable out of the backing plate
    • Remove the bolts from the hub assembly
  6. step : Removing the Hub Assembly (15:40)
    • Insert the stuck hub into a bearing press tool
    • If needed, heat up the plate
    • Let the plate cool
    • Press the hub out of the backing plate
  7. step : Installing the New Brake Shoes (20:55)
    • Pull the emergency cable into the backing plate
    • Tighten the 10mm bolt to the backing plate
    • Pry the emergency brake cable into the front brake shoe slot with vise grip pliers
    • Lift the front brake shoe into place
    • Thread the retaining pin/nail into the brake shoe from the back
    • Twist on the spring and retainer to the nail with vise grip pliers
    • Put the rear brake shoe into place
    • Thread the retaining pin/nail into the brake shoe from the back
    • Twist on the spring and retainer to the nail with vise grip pliers
    • Put the adjuster into place
    • Put the upper adjustor in place
    • Push the brake shoes together by hand
    • Put the adjuster clip into place
    • Hook the longer springs on with the vise grip pliers
  8. step : Reinstalling the Brake Pads and Rotor (27:17)
    • Connect the ABS sensor connector
    • Put the rotor on backwards
    • Clean off the rotor with brake parts cleaner
    • Put the rotor into place
    • Place an old brake pad in the caliper Compress the caliper piston with a c-clamp and brake pad
    • Insert the caliper bracket into place
    • Tighten the 14mm bolt to the caliper bracket
    • Apply grease to the brake pad tabs
    • Put the brake pads in the caliper bracket
    • Place the caliper on
    • Tighten the 14mm bolt to the caliper
    • Torque the caliper bolts to 46 foot-pounds
    • Adjust the brake shoes so that they have little resistance to the rotor
  9. step : Reattaching the Wheel (31:30)
    • Slide the wheel into place
    • Start the lug nuts by hand with the taper to the wheel
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Jack Stands
  • Rubber Mallet
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner
  • Bungee Cord
  • Cloth Rags

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 21mm Socket
  • 10mm Socket

  • Specialty Tools

  • Dead Blow Hammer

  • Wrenches - Metric

  • 14mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2002-2003Lexus ES300 Lexus ES300 Rear Wheel Bearing & Hub Assembly Passenger Side TRQ
2004-2006Lexus ES330 Lexus ES330 Rear Wheel Bearing & Hub Assembly Passenger Side TRQ
2007Lexus ES350 Lexus ES350 Rear Wheel Bearing & Hub Assembly Passenger Side TRQ
2005-2012Toyota Avalon Toyota Avalon Rear Wheel Bearing & Hub Assembly Passenger Side TRQ
2002-2004Toyota Camry Toyota Camry with ABS Brakes Rear Wheel Bearing & Hub Assembly Passenger Side TRQ
2005-2011Toyota Camry Toyota Camry Rear Wheel Bearing & Hub Assembly Passenger Side TRQ
2001-2003Toyota Highlander Toyota Highlander Front Wheel Drive Rear Wheel Bearing & Hub Assembly Passenger Side TRQ
2004-2008Toyota Solara Toyota Solara Rear Wheel Bearing & Hub Assembly Passenger Side TRQ

This part replaces:

  • Hollander 538-58859R
  • TRQ BHA54205
  • OE # 4245048011
Part #: 1ASHR00063


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA54205

How-to Video:

(33:08 min)