Replaces

Wheel Bearing & Hub Assembly TRQ BHA54165 - 1ASHR00013

Part Details

  • Bearing Type: Ball Bearing

Specifications:

  • Fits either the LH (Driver Side) & RH (Passenger Side) REAR
  • Direct replacement
  • Has ABS sensor
  • Built to strict quality control standards

 

Precision Engineered

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.
100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:02)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Drum (1:18)
    • Spray rust penetrant on the lug studs
    • Pry off the drum with flat blade screwdrivers
    • Pull off the drum
  3. step : Removing the Brake Shoes (1:44)
    • Remove the brake shoe springs with the vise grip pliers
    • Hold the front retaining pin in place by hand
    • Pry out the front retaining spring with a flat blade screwdriver
    • Remove the brake shoe
    • Remove the brake adjuster
    • Pry the emergency brake cable out of the front brake shoe
  4. step : Removing the Wheel Hub (3:14)
    • Disconnect the wheel speed sensor wiring harness
    • Loosen the four T50 Torx bolts from the wheel hub
    • Loosen the wheel hub with a hammer and chisel
    • Remove the four T50 Torx bolts from the wheel hub
    • Pry out the hub with a pry bar
    • Clean the wheel spindle with a wire brush
  5. step : Installing the New Wheel Hub (4:54)
    • Put the hub into place with the wheel speed sensor toward the back of the car
    • Insert the four T50 bolts into the wheel hub
    • Tighten the T50 bolts to 45 foot-pounds of torque
  6. step : Installing the New Brake Shoes (3:41)
    • Pry the emergency brake cable into the front brake shoe slot with vise grip pliers
    • Lift the front brake shoe into place
    • Thread the retaining pin into the brake shoe
    • Put the adjuster into place
    • Remove the adjuster clip
    • Put the rear brake shoe into place
    • Thread the retaining pin into the brake shoe
    • Put white grease on both ends of the adjuster clip
    • Insert the adjuster end into place
    • Twist on the retaining spring
    • Clean the brake shoes with mineral spirits
    • Hook the springs on with the vise grip pliers
  7. step : Installing the New Brake Drum (5:59)
    • Try to slide the brake drum on
    • If necessary turn the adjuster wheel with a flat blade screwdriver
    • The brake rotor should slide on with some resistance
  8. step : Reattaching the Wheel (6:12)
    • Slide the wheel into place
    • Start the 19mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  9. step : Testing the Brakes (9:10)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Chisel
  • Wire Brush
  • Hammer
  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Lug Wrench

  • Ratchets & Related

  • Socket Extensions
  • 3/8 Inch Breaker Bar
  • Torque Wrench
  • 3/8 Inch Drive Ratchet
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 19mm Socket

  • Torx Drivers & Sockets

  • T50 Torx Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1992Buick LeSabre Buick LeSabre Wheel Bearing & Hub Assembly Rear for Models with ABS Brakes TRQ
1993-1999Buick LeSabre Buick LeSabre Wheel Bearing & Hub Assembly Rear TRQ
1991-1992Buick Park Avenue Buick Park Avenue Wheel Bearing & Hub Assembly Rear for Models with ABS Brakes TRQ
1993-1996Buick Park Avenue Buick Park Avenue Wheel Bearing & Hub Assembly Rear TRQ
1991-1993Cadillac Deville Cadillac Deville Wheel Bearing & Hub Assembly Rear TRQ
1991-1993Cadillac Fleetwood Cadillac Fleetwood Wheel Bearing & Hub Assembly Rear TRQ
1992Oldsmobile 88 Olds 88 Wheel Bearing & Hub Assembly Rear for Models with ABS Brakes TRQ
1993-1999Oldsmobile 88 Olds 88 Wheel Bearing & Hub Assembly Rear TRQ
1991-1992Oldsmobile 98 Olds 98 Wheel Bearing & Hub Assembly Rear for Models with ABS Brakes TRQ
1993-1996Oldsmobile 98 Olds 98 Wheel Bearing & Hub Assembly Rear TRQ
1992Pontiac Bonneville Pontiac Bonneville Wheel Bearing & Hub Assembly Rear for Models with ABS Brakes TRQ
1993-1999Pontiac Bonneville Pontiac Bonneville Wheel Bearing & Hub Assembly Rear TRQ

This part replaces:

  • Hollander 538-01270
  • TRQ BHA54165
  • OE # 7470541
Part #: 1ASHR00013


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA54165

How-to Video:

(09:44 min)