Replaces

Wheel Bearing & Hub Assembly TRQ BHA53775 - 1ASHS00909

Specifications:

  • Brand New Wheel Bearing & Hub Assemblies
  • Comes as a Set of 4
    • Fits both LH (Driver Side) & RH (Passenger Side) Front & Rear
  • 3 Bolt Flanges
  • Fits 5 Lug Wheels
  • Direct replacements
  • Built to strict quality control standards
Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:25)
    • Pry out the center cap with a pick
    • Loosen the 35mm hub nut with a breaker bar
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:37)
    • Spray rust penetrant in the hub nut
    • Loosen the 35mm nut
    • Thread the nut on a few threads
    • Tap the nut with a mallet to loosen the axle
  3. step : Removing the Brakes (2:37)
    • Loosen the 14mm caliper bolts
    • Secure the caliper with a bungee cord
    • Remove the 18mm caliper bracket bolts
    • Remove the caliper bracket and the pads
    • Remove the T30 Torx bolt from the rotor
    • Remove the rotor
  4. step : Removing the ABS Sensor (4:25)
    • Remove the 10mm bolt from the ABS sensor
    • Remove the ABS sensor
  5. step : Removing the Hub (4:50)
    • Remove the three 13mm bolts from the hub
    • Tap the hub out from the knuckle
    • Remove the hub from the axle
  6. step : Installing the New Hub (7:06)
    • Clean any corrosion from the axle splines with brake cleaner and a wire brush
    • Apply anti-seize grease around the knuckle cavity
    • Slide the hub over the axle
    • Tighten the three 13mm bolts to the hub
    • Torque the bolts to 74 foot-pounds
  7. step : Reinstalling the ABS Sensor (9:17)
    • Insert the ABS sensor into place
    • Tighten the 10mm bolt to the ABS sensor
  8. step : Reinstalling the Axle Nut (9:51)
    • Thread the axle nut on by hand
    • Tighten the 35mm axle nut
  9. step : Installing the Caliper Bracket and Rotor (10:15)
    • Insert the rotor to the hub
    • Tighten the T30 Torx bolt to the rotor
    • Put the caliper bracket back into place
    • Start the 18mm bolts by hand
    • Tighten the bolts to 140 foot-pounds of torque
  10. step : Installing the Brake Caliper (11:17)
    • Press the metal clip to the brake pad
    • Put an old pad in the caliper
    • Apply grease to the brake pad tabs
    • Use a large C-clamp and the old pad to push the pistons back if needed
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread bolts by hand
    • Tighten the 14mm bolts to 20 foot-pounds
    • Clean the rotor with brake parts cleaner or mineral spirits
  11. step : Reattaching the Wheel (11:54)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 125 foot-pounds in a crossing or star pattern
    • Torque the hub nut to 151 foot-pounds
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Jack Stands
  • Rubber Mallet
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner
  • Paper Towels
  • Bungee Cord
  • Anti-Seize Grease

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • Swivel
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 35mm Socket
  • 14mm Socket
  • 18mm Socket
  • 10mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2010 Buick Allure Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
  • 2010-2016 Buick LaCrosse Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
  • 2011-2016 Buick Regal Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
  • 2013-2016 Cadillac XTS Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set without Heavy Duty Brakes TRQ
  • 2014-2017 Chevy Impala Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
  • 2013-2016 Chevy Malibu Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
  • 2010-2011 Saab 9-5 Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ

This part replaces:

  • Hollander 538-00223
  • OE # 13502886
  • OE # 13504972
  • TRQ BHA53775
Part #: 1ASHS00909


TRQ
Brand #: BHA53775

How-to Video:

(13:18 min)