Replaces

Wheel Bearing & Hub Assembly TRQ BHA53657 - 1ASHS00616

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
    Direct Fit Replacement
    Precision Engineered
    Highest Quality Materials
  • Bearing Type: Ball Bearing
  • Quantity: 4 Piece Set

These replacement wheel bearing & hub assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Comes as a SET of 4
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT & REAR
  • Replaces dealer part numbers: 4582220, 4779011
  • 4 Bolt Flanges
  • Fit 5 Lug Wheels
  • Have ABS with Tone Ring Sensors
  • Studs already installed
  • Direct replacements
  • Built to strict quality control standards
These wheel bearing & hub assemblies are great replacements and have good cost savings over units from the dealer.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:08)
    • Loosen the Lug Nuts
    • Raise the vehicle with a jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Slide off the wheel
  2. step : Removing the Brakes (1:36)
    • Using a pry bar, pull the brake caliper forward to reset the piston
    • Remove the 10mm sockets from the brake caliper
    • Pull off the brake caliper
    • Pull off the brake rotor
  3. step : Adjusting the Emergency Brake (3:01)
    • If the rotor does not remove easily, adjust the emergency brakes
    • Remove the rubber plug in the back with a flat blade screwdriver
    • Use a brake spoon to turn the adjuster wheel down
  4. step : Removing the Hub (4:08)
    • Using a hammer and chisel, remove the dust cover
    • Break the cotter pin with the slip joint pliers
    • Use a 36mm socket with a breaker bar and a pipe to loosen the nut
    • Remove the nut
    • Pull off the hub
  5. step : Installing the New Hub (5:35)
    • Remove rust with paper towel or wire brush
    • Apply lubricant if necessary
    • Slide on the new hub
    • Secure the hub in place with a block of wood and a hammer
    • Reattach the nut and tighten it with the breaker bar
    • Tighten the nut to 124 foot-pounds with the torque wrench
    • Attach the spring washer and insert the cotter pin
    • Secure the cotter pin using the pliers
    • Reattach the dust cover using the hammer
  6. step : Reinstalling the Brake Rotor (8:24)
    • Slide on the brake rotor
    • Use the brake spoon to adjust the emergency brake
    • There should be even friction all around from the emergency brake shoes
    • Replace the rubber plug
  7. step : Reinstalling the Brake Caliper and Pads (8:54)
    • Reattach the pads to the caliper
    • Push back the caliper slides
    • Put the caliper into place
    • Slide in the 10mm bolts from behind
    • Begin threading the bolts by hand
    • Tighten the bolts with the 10mm socket
    • Tighten the bolts to 20 foot-pounds with the torque wrench
  8. step : Reinstalling the Wheel (11:12)
    • Slide the wheel on
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle
    • Torque the lug nuts to between 90 and 100 foot-pounds
  9. step : Testing the Brakes (11:34)
    • Pump the brakes repeatedly
    • Press the brake pedal
    • Put the vehicle into gear
    • Make sure the brakes hold the vehicle in gear
    • Test the brakes at5 miles per hour
    • Test the brakes at10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Chisel
  • Floor Jack
  • Hammer
  • Jack Stands
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Paper Towels

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench
  • Slip-Joint Pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 19mm Socket
  • 36mm Socket

  • Specialty Tools

  • Brake Spoon

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1999-2004Chrysler 300M Chrysler 300M Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
1993-1996Chrysler Concorde Chrysler Concorde Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
1997Chrysler Concorde Chrysler Concorde Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with Disc Brakes TRQ
1998-2004Chrysler Concorde Chrysler Concorde Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with ABS Brakes TRQ
1994-1997Chrysler LHS Chrysler LHS Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
1999-2001Chrysler LHS Chrysler LHS Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
1994-1996Chrysler New Yorker Chrysler New Yorker Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
1993-1997Dodge Intrepid Dodge Intrepid Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with Disc Brakes TRQ
1998-2004Dodge Intrepid Dodge Intrepid Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with ABS Brakes TRQ
1993-1996Eagle Vision Eagle Vision Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set TRQ
1997Eagle Vision Eagle Vision Front & Rear Wheel Bearing & Hub Assembly 4 Piece Set for Models with Disc Brakes TRQ

This part replaces:

  • TRQ BHA53657
Part #: 1ASHS00616


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA53657

How-to Video:

(12:08 min)