Replaces

Wheel Bearing & Hub Assembly Timken SP470200 - TKSHF00020

TIMKEN WHEEL BEARING & HUB ASSEMBLY: SP470200

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • 3 Bolt Flange
  • Fits 5 Lug Wheel
  • Replaces dealer part numbers: 1L24-1104AC, 1L24-1104AD, 1L24-1104AE, 1L24-1104AF, 1L24-1104AG, 1L24-1K018AB, 1L2Z-1104AA, 1L2Z-1104AB, 2L24-1104AA, 2L24-1K018AB, 2L2Z-1104AA, 2L2Z-1104AB, 3L24-1K018AA, 3L24-1K018AB, 3L2Z-1104AB, 4L2Z-1104AA, 1L241104AC, 1L241104AD, 1L241104AE, 1L241104AF, 1L241104AG, 1L241K018AB, 1L2Z1104AA, 1L2Z1104AB, 2L241104AA, 2L241K018AB, 2L2Z1104AA, 2L2Z1104AB, 3L241K018AA, 3L241K018AB, 3L2Z1104AB, 4L241K018AA, 4L2Z1104AA, 3C5Z 1104 AA, 3C5Z1104AA
  • Studs already installed
  • Includes ABS sensor and plug wire
  • Direct replacement
  • Built to strict quality control standards
  • Does NOT fit Sport or Sport Trac Models

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:48)
    • Pry off the center cap with a flat blade screwdriver
    • Remove the hub nut with a 30mm socket and ratchet
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:33)
    • Pry the ABS sensor wiring out of its clips with a flat blade screwdriver
    • Remove the two 14mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Hold the brake caliper aside with wire ties
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (3:19)
    • Remove the two 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  4. step : Removing the Hub (3:40)
    • Disconnect the ABS sensor wiring harness in the engine compartment
    • Unclip the ABS sensor wiring
    • Pull out the ABS sensor wire
    • Make sure the axle can move freely in and out of the hub
    • Apply rust penetrant to the hub bolts
    • Remove the three 15mm bolts from the hub
    • Pull off the hub
  5. step : Installing the Hub (5:37)
    • Push the hub onto the axle with the ABS sensor on top
    • Insert the three 15mm bolts into the hub
    • Tighten the hub bolts to 75 foot-pounds of torque
    • Feed the ABS sensor wire into place
    • Fasten the hub nut onto the hub
  6. step : Installing the Brake Rotor (7:40)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Put the bracket back into place
    • Start the two 18mm bolts by hand
    • Tighten the bolts to 85 foot-pounds
  7. step : Installing the Brake Pads (8:27)
    • Apply brake grease to the brake pad tabs
    • Install the new brake pads into the bracket
    • Remove the wire ties from the caliper
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten bolts to 25 foot-pounds
    • Push the ABS sensor wire into its clips
    • Clean the brake rotor
  8. step : Reattaching the Wheel (10:04)
    • Remove the placeholder lug nut
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut to 180 foot-pounds
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  9. step : Connecting the ABS Sensor (10:50)
    • Connect the ABS sensor wiring harness inside the engine compartment
  10. step : Testing the Brakes (11:03)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    Allen Wrenches

  • 5mm Allen Wrench

  • General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • White Grease

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 30mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2002-2005Ford Explorer Ford Explorer 4 Door Front Wheel Bearing & Hub Assembly Timken SP470200
2003-2005Lincoln Aviator Lincoln Aviator Front Wheel Bearing & Hub Assembly Timken SP470200
2002-2005Mercury Mountaineer Mercury Mountaineer Front Wheel Bearing & Hub Assembly Timken SP470200

This part replaces:

  • Timken SP470200
  • OE # 4L2Z 1104 AA
  • OE # 3L2Z 2C204 AA
  • Hollander 538-01585
Only 4 left in stock
Part #: TKSHF00020


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: SP470200

How-to Video:

(11:32 min)