Replaces

Wheel Bearing & Hub Assembly Timken HA590030 - TKSHF00220

TIMKEN WHEEL BEARING & HUB ASSEMBLY: HA590030

This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Replaces dealer part number: 4779199AA
  • Fits 5 Lug Wheel
  • Studs already installed
  • Direct replacement
  • Built to strict quality control standards
  • Fits RWD (Rear Wheel Drive) Models only
    • Does NOT fit AWD (All Wheel Drive) Models

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:09)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:21)
    • Hold the wheel studs with a brake rotor
    • Remove the two 13mm bolts from the caliper bracket
    • Pull the caliper off
    • Put the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (1:46)
    • Remove the two 18mm bolts from the caliper bracket
    • Pull off the brake caliper bracket
    • Strike the drum surface of the rotor with a hammer to loosen the rotor
    • Pull the rotor off
    • Clean the hub surface with a wire brush
  4. step : Removing the Hub Assembly (2:12)
    • Tap between the hub and dust cover with a hammer and chisel
    • Remove the dust cover
    • Remove the 35mm center nut
    • Remove the wheel hub and bearing
  5. step : Installing the Hub Assembly (4:03)
    • Insert the wheel hub into the spindle
    • Install the 35mm nut
    • Torque the nut to 184 foot-pounds
    • Install the dust shield
  6. step : Preparing the New Brake Pads and Rotors (5:00)
    • Pry off the brake pad shims with a flat blade screwdriver
    • Clean the brake pad shims with a wire brush
    • Clean the caliper bracket with a wire brush
    • Apply brake grease to the shim-mounting area of the caliper bracket
    • Place the shim onto the caliper bracket
    • Apply grease to the caliper shims
    • Pull out the caliper slides
    • Apply grease to the caliper slides
    • Push the caliper slide into the caliper
  7. step : Installing the Brake Rotor (7:23)
    • Apply grease to the hub surface
    • Put the rotor onto the hub backwards
    • Spray the rear of the hub with brake cleaner
    • Pull off the brake rotor
    • Slide the brake rotor on
    • Spray the front of the rotor with brake cleaner
    • Put the caliper bracket into place
    • Insert the two 18mm bolts into the caliper bracket
    • Tighten the two 18mm bolts to 70 foot-pounds of torque
  8. step : Installing the Brake Pads (8:49)
    • Put the brake pads into the caliper bracket
    • Apply grease to the back of the brake pads
    • Push back the caliper piston with grove lock pliers
    • Put the brake caliper into place
    • Insert the two 13mm bolts into the caliper
    • Tighten the two 13mm bolts to 44 foot-pounds of torque
  9. step : Reattaching the Wheel (9:53)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Rubber Mallet
  • Chisel
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Paper Towels
  • Anti-Seize Grease
  • Brake Parts Cleaner
  • Gloves
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 35mm Socket
  • Complete Metric Socket Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2005-2011Chrysler 300 Chrysler 300 Rear Wheel Drive Front Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590030
2012-2014Chrysler 300 Chrysler 300 SRT-8 Front Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590030
2008-2011Dodge Challenger Dodge Challenger Front Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590030
2012-2014Dodge Challenger Dodge Challenger SRT-8 Front Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590030
2006-2011Dodge Charger Dodge Charger Rear Wheel Drive Front Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590030
2012-2014Dodge Charger Dodge Charger SRT-8 Front Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590030
2005-2008Dodge Magnum Dodge Magnum Rear Wheel Drive Front Wheel Bearing & Hub Assembly Driver or Passenger Side Timken HA590030

This part replaces:

  • Timken HA590030
  • Hollander 538-01735
  • OE # 4779199AA
Only 4 left in stock
Part #: TKSHF00220


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: HA590030

How-to Video:

(10:22 min)