Replaces

Wheel Bearing & Hub Assembly Timken 513100 - TKSHS00033

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

TIMKEN WHEEL BEARING & HUB ASSEMBLY PAIR: 513100

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assemblies
  • Comes as a PAIR:
    • Includes both the LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacement
  • Replaces dealer part numbers: 3F132C300BA, 3F13-2C300-BA, 3F1Z1104BA, 3F1Z-1104-BA, F50Y1104A, F50Y-1104-A, F8RZ1104AA, F8RZ-1104-AA, XFI22C300BB, XFI2-2C300-BB, XFIZ1104AEB, XFIZ-1104AE-B, XFIZ1104BA, XFIZ-1104-BA
  • Fits 5 lug wheel
  • Wheel studs already installed

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove Wheel (1:09)
    • Remove hub nut
    • Remove lug nuts and remove wheel with an 18mm socket.
  2. step : Remove tie rod (1:50)
    • Remove cotter pin.
    • Use your 18 mm socket to remove the nut at the bottom of the tie rod.
    • Use your tie rod puller to pull the tie rod up.
    • Use your two adjustable wrenches to remove the tie rod.
  3. step : Remove the axle. (2:42)
    • Disconnect the brake line bracket and ABS sensor
    • Remove the upper stabilizer bolt with an 18mm wrench and a 10 mm wrench to secure it.
    • Remove the lower stabilizer bolt using your 18 mm wrench to secure it and a 21 mm socket.
    • Use a hammer to drive the bolt all the way out.
    • Move the steering knuckle off the strut with a hammer.
    • Tap the axle with a hammer and use a pry bar to pry it out of the steering knuckle.
    • Pry the other end of the axle out.
  4. step : Remove Brake Caliper (6:00)
    • Use your 12mm and 15mm socket wrenches to remove the calipers and caliper brackets.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
    • Use a wire tie to secure the caliper up out of the way.
  5. step : Remove the brake rotor (7:00)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  6. step : Remove Hub (7:08)
    • On this vehicle, the hub is cast iron and the knuckle is aluminum, seizing is a potential issue.
    • Use an air hammer and protective eyewear to break the hub free if this happens.
    • Remove the hub with a hammer.
    • Clean up any corrosion with a wire brush.
  7. step : Install new hub (9:26)
    • Use some penetrating oil or anti-seize grease to prep the knuckle for the new hub.
    • Put the three 15 mm bolts in place and tighten the nuts to 70 ft lbs.
    • Check out our other videos to see how to finish putting everything back together.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Large Hammer
  • Jack Stands
  • Wire Brush
  • Hammer

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Sockets - Metric

  • 15mm Socket
  • 11mm Socket
  • 18mm Socket
  • 14mm Socket
  • 21mm Socket
  • 10mm Socket
  • 12mm Socket
  • 17mm Socket
  • 20mm Socket
  • 19mm Socket
  • 13mm Socket
  • 16mm Socket

  • Specialty Tools

  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench
  • 10mm Wrench
  • 13mm Wrench
  • 17mm Wrench
  • 12mm Wrench
  • 15mm Wrench
  • 14mm Wrench
  • 11mm Wrench
  • 16mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1996-2006Ford Taurus Ford Taurus Wheel Bearing & Hub Assembly Front Pair Timken 513100
1995-2002Lincoln Continental Lincoln Continental Wheel Bearing & Hub Assembly Front Pair Timken 513100
1996-2005Mercury Sable Mercury Sable Wheel Bearing & Hub Assembly Front Pair Timken 513100
Only 2 left in stock
Part #: TKSHS00033


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: 513100

How-to Video:

(09:55 min)