Wheel Bearing & Hub Assembly Rear TRQ BHA54181 - 1ASHR00035

This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.


  • Fits either LH (Driver Side) or RH (Passenger Side) REAR
  • Replaces dealer part numbers: 4582220, 4779011
  • 4 Bolt Flange
  • Fits 5 Lug Wheels
  • Has ABS Tone Ring Sensor, but will also work on non-ABS models without issue
  • Studs already installed
  • Direct replacement
  • Built to strict quality control standards
This wheel bearing & hub assembly is a great replacement and has good cost savings over a unit from the dealer.


  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.


  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.
Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

BHA54181 Axle / Spindle Nut Torque Specification
  1. step : Removing the Wheel (1:08)
    • Loosen the Lug Nuts
    • Raise the vehicle with a jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Slide off the wheel
  2. step : Removing the Brakes (1:36)
    • Using a pry bar, pull the brake caliper forward to reset the piston
    • Remove the 10mm sockets from the brake caliper
    • Pull off the brake caliper
    • Pull off the brake rotor
  3. step : Adjusting the Emergency Brake (3:01)
    • If the rotor does not remove easily, adjust the emergency brakes
    • Remove the rubber plug in the back with a flat blade screwdriver
    • Use a brake spoon to turn the adjuster wheel down
  4. step : Removing the Hub (4:08)
    • Using a hammer and chisel, remove the dust cover
    • Break the cotter pin with the slip joint pliers
    • Use a 36mm socket with a breaker bar and a pipe to loosen the nut
    • Remove the nut
    • Pull off the hub
  5. step : Installing the New Hub (5:35)
    • Remove rust with paper towel or wire brush
    • Apply lubricant if necessary
    • Slide on the new hub
    • Secure the hub in place with a block of wood and a hammer
    • Reattach the nut and tighten it with the breaker bar
    • Tighten the nut to 124 foot-pounds with the torque wrench
    • Attach the spring washer and insert the cotter pin
    • Secure the cotter pin using the pliers
    • Reattach the dust cover using the hammer
  6. step : Reinstalling the Brake Rotor (8:24)
    • Slide on the brake rotor
    • Use the brake spoon to adjust the emergency brake
    • There should be even friction all around from the emergency brake shoes
    • Replace the rubber plug
  7. step : Reinstalling the Brake Caliper and Pads (8:54)
    • Reattach the pads to the caliper
    • Push back the caliper slides
    • Put the caliper into place
    • Slide in the 10mm bolts from behind
    • Begin threading the bolts by hand
    • Tighten the bolts with the 10mm socket
    • Tighten the bolts to 20 foot-pounds with the torque wrench
  8. step : Reinstalling the Wheel (11:12)
    • Slide the wheel on
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle
    • Torque the lug nuts to between 90 and 100 foot-pounds
  9. step : Testing the Brakes (11:34)
    • Pump the brakes repeatedly
    • Press the brake pedal
    • Put the vehicle into gear
    • Make sure the brakes hold the vehicle in gear
    • Test the brakes at5 miles per hour
    • Test the brakes at10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Chisel
  • Floor Jack
  • Hammer
  • Jack Stands
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Paper Towels

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench
  • Slip-Joint Pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 19mm Socket
  • 36mm Socket

  • Specialty Tools

  • Brake Spoon

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2004 Chrysler 300M Rear Wheel Bearing & Hub Assembly TRQ
  • 1993-1996 Chrysler Concorde Rear Wheel Bearing & Hub Assembly TRQ
  • 1997 Chrysler Concorde Rear Wheel Bearing & Hub Assembly for Models with Disc Brakes TRQ
  • 1998-2004 Chrysler Concorde Rear Wheel Bearing & Hub Assembly TRQ
  • 1994-1997 Chrysler LHS Rear Wheel Bearing & Hub Assembly TRQ
  • 1999-2001 Chrysler LHS Rear Wheel Bearing & Hub Assembly TRQ
  • 1994-1996 Chrysler New Yorker Rear Wheel Bearing & Hub Assembly TRQ
  • 1993-1997 Dodge Intrepid Rear Wheel Bearing & Hub Assembly for Models with Disc Brakes TRQ
  • 1998-2004 Dodge Intrepid Rear Wheel Bearing & Hub Assembly TRQ
  • 1993-1996 Eagle Vision Rear Wheel Bearing & Hub Assembly TRQ
  • 1997 Eagle Vision Rear Wheel Bearing & Hub Assembly for Models with Disc Brakes TRQ

This part replaces:

  • Hollander 538-01290 538-01465B
  • OE # 4582220 4779011
  • TRQ BHA54181
Part #: 1ASHR00035

Ships Same Day for orders placed by 4 P.M. ET

Brand #: BHA54181

How-to Video:

(12:08 min)