Replaces
Wheel Bearing & Hub Assembly Rear Timken 513121 - TKSHX00012
TKSHX00012TIMKEN WHEEL BEARING & HUB ASSEMBLY: 513121
Specifications:
- Brand New Timken Hub Assembly
- Fits LH (Driver Side) or RH (Passenger Side) REAR
- Direct replacement
- Wheel studs already included and installed
- Replaces dealer part numbers: 7470017, 7470105, 7470143, 7470567, 7470568, 12429204
- Has ABS sensor w/stainless steel sensor wire clip
- Built to strict quality control standards
- For AWD (All Wheel Drive) models only
Note: These parts are authentic Timken brand products that are supplied and packaged by Timken. In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.
Lifetime Warranty
This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.
-
step : Remove the wheel and tire (1:30)
- Raise and secure the vehicle.
- Remove the lug nuts and then the wheel.
-
step : Remove Caliper (2:00)
- Turn wheels all the way in the opposite direction of the side you are working on.
- Use your 15mm socket wrench to remove the caliper bolts.
- Use a wire tie to help prevent stress on the caliper.
-
step : Remove brake disk (2:44)
- Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
-
step : Remove Hub (2:56)
- Remove the 3 bolts securing the hub using your 13mm socket and 3/8 extension and ratchet or breaker bar.
- You can use penetrating oil to help.
- Use a 35mm socket to remove the hub nut.
- Give the axle a slight tap with a hammer to loosen it.
- Use a rubber mallet to break it free, and work around the flange with the hammer to pull it off.
- Leave the top 13mm loosely still in to prevent the hub from flying out if you hit it too hard.
- Remove the hub, using driving tools to help work it out of the steering knuckle.
- Clean up any corrosion with a wire brush.
-
step : Install new hub (8:30)
- Use some penetrating oil to prep the knuckle for the new hub.
- Watch part 2 to install your new 1A Auto hub!
Tools needed for replacement:
- Floor Jack
- Hammer
- Jack Stands
- Rubber Mallet
- Rust Penetrant
- 1/2 Inch Breaker Bar
- Ratchet
- Socket Extensions
- Torque Wrench
- Phillips Head Screwdriver
- 13mm Socket
- 19mm Socket
- 32mm Socket
- 35mm Socket
General Tools
Materials, Fluids, and Supplies
Ratchets & Related
Screwdrivers & Related
Sockets - Metric
Vehicle Fit
- 2002-2006 Buick Rendezvous All Wheel Drive Rear Wheel Bearing & Hub Assembly Timken 513121
- 2002-2005 Chevy Venture All Wheel Drive Rear Wheel Bearing & Hub Assembly Timken 513121
- 2002-2004 Olds Silhouette All Wheel Drive Rear Wheel Bearing & Hub Assembly Timken 513121
- 2001-2005 Pontiac Aztek All Wheel Drive Rear Wheel Bearing & Hub Assembly Timken 513121
- 2002-2004 Pontiac Montana All Wheel Drive Rear Wheel Bearing & Hub Assembly Timken 513121
- 2005 Pontiac Montana All Wheel Drive Base Model Rear Wheel Bearing & Hub Assembly Timken 513121
This part replaces:
- Timken 513121
- OE # TKSHX00012