Replaces

Wheel Bearing & Hub Assembly Rear Pair TRQ BHA53462 - 1ASHS00209

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) REAR
  • 4 Bolt Rectangular Flanges
  • Fits 5 Lug Wheels
  • Replaces dealer part numbers: 12403095, 88964177
  • Studs already installed
  • Built to strict quality control standards
  • Fit models with ABS - RPO Code "JL9"
  • Have ABS sensors built in with correct plug configuration
  • Fit FWD (Front Wheel Drive) Models only
Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:59)
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the center cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:23)
    • Remove the two 14mm bolts from the brake caliper
    • Pull the caliper aside
    • Pull the brake pads off
  3. step : Removing the Brake Rotor (2:04)
    • Remove the two 13mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Hold the rotor in place with a flat blade screwdriver
    • Remove the T30 Torx screw from the rotor
    • Strike the rotor with a hammer to loosen it
    • Pull the rotor off
  4. step : Removing the Wheel Hub (3:16)
    • Remove the four 10mm bolts from the wheel hub
    • Disconnect the ABS wiring harness from the hub
    • Strike the hub with a hammer to remove it
    • Push out the emergency brake cable pin with a hammer and a screwdriver
    • Pull the spring off the brake backing plate with a screwdriver
    • Pull the emergency brake cable out of the brake backing plate
  5. step : Separating the Wheel Hub from the Brake Backing Plate (5:01)
    • Remove the two T30 screws from the backing plate
    • Pull the bracket off of the backing plate
    • Pull the backing plate off of the hub
    • Pull the emergency brake ring off of the hub
  6. step : Preparing the New Wheel Hub (5:35)
    • Clean the hub mounting area with a wire brush
    • Apply white grease or bearing grease to the mounting area
    • Put the emergency brake ring onto the backing plate
    • Put the hub through the ring and backing plate, making sure the ABS wiring connector is lined up with the backing plate hole
    • Pull the arm off the emergency brake activator
    • Put the emergency brake activator onto the ring
    • Attach the bracket to the backing plate
    • Insert the two T30 screws into the bracket
    • Push the emergency brake arm into place through the bracket
  7. step : Installing the New Wheel Hub (7:39)
    • Attach the emergency brake cable to the emergency brake arm
    • Push the emergency brake cable into its bracket
    • Insert the pin into the bracket, using a hammer
    • Attach the spring to the emergency brake arm
    • Pull the spring onto the bracket with vise-grip pliers
    • Push the hub into place
    • Start one of the 10mm bolts to hold the hub in place
    • Start the remaining three 10mm bolts
    • Tighten the four 10mm bolts to 45 - 50 foot-pounds of torque
    • Reconnect the ABS wiring harness
    • Adjust the emergency brake, by turning the wheel with a flat blade screwdriver
  8. step : Reinstalling the Brake Rotor (9:43)
    • Slide the rotor on
    • Adjust the emergency brake further, if necessary
    • Insert the T30 screw into the rotor
    • Put the bracket back into place
    • Start the two 13mm bolts by hand
    • Tighten the bolts to 75 foot-pounds of torque
  9. step : Reinstalling the Brake Pads (10:45)
    • Apply grease to the brake pads
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten bolts to 30 foot-pounds
  10. step : Reattaching the Wheel (11:27)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 14mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

5.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
3
0
0
0
0
Parts shopping made simple
Needed rear hubs for my daughters car. Auto parts store wanted $250 for the pair. I just couldnt pay that. I have purchased quality parts from 1A auto be for. Difficult parts like exhaust manifolds. A pair of hubs were $71. A no brainer in my opinion. These parts were exact fit which made in easy to install. Fast ship to. Sorry but auto parts stores are ripping everyone off for there convenience.
August 28, 2017
Purchased
8 months ago
The Best 1AAuto
They are the best I don't have problem with them thanks to 1AAuto that's were everyone should buy there parts they the best and they not expensive they are real low price thanks 1AAuto
December 4, 2017
Purchased
5 months ago
Great Product
Great product for a wonderful price! Had a friend put them on my car and did not take long at all. I have not had any problems with them yet and I do not miss the noise my old ones made.
April 16, 2018
Purchased
3 weeks ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2008 Buick Allure Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Pair TRQ
  • 2009 Buick Allure Rear Wheel Bearing & Hub Assembly Pair TRQ
  • 2005-2008 Buick LaCrosse Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Pair TRQ
  • 2009 Buick LaCrosse Rear Wheel Bearing & Hub Assembly Pair TRQ
  • 2005 Buick Terraza Rear 4 Bolt Flange Wheel Bearing & Hub Assembly Pair Front Wheel Drive TRQ
  • 2006-2008 Chevy Impala Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Pair TRQ
  • 2009-2013 Chevy Impala Rear Wheel Bearing & Hub Assembly Pair TRQ
  • 2006-2007 Chevy Monte Carlo Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Pair TRQ
  • 2005 Chevy Uplander Rear 4 Bolt Flange Wheel Bearing & Hub Assembly Pair Front Wheel Drive TRQ
  • 2004-2008 Pontiac Grand Prix Rear Wheel Bearing & Hub Assembly for Models with ABS Brakes Pair TRQ
  • 2005 Pontiac Montana SV6 Rear 4 Bolt Flange Wheel Bearing & Hub Assembly Pair Front Wheel Drive TRQ
  • 2005 Saturn Relay Rear 4 Bolt Flange Wheel Bearing & Hub Assembly Pair Front Wheel Drive TRQ

This part replaces:

  • TRQ BHA53462
Part #: 1ASHS00209



TRQ
Brand #: BHA53462

How-to Video:

(12:19 min)