Replaces

Wheel Bearing & Hub Assembly Pair TRQ BHA53476 - 1ASHS00332

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) REAR
  • Direct replacements
  • Have ABS with Integral Sensors installed
  • 4 bolt rectangular flanges
  • Fits 5 Lug Wheels
  • Studs already installed
  • Built to strict quality control standards
  • Fits ALL models (both 2WD & 4WD)

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hubs & bearings are all tested prior to shipping.

Fit Guaranteed

  • These hub & bearing sets will install just as your originals do. You can use your existing hardware.
  • Save time and money with direct fit hub bearing assemblies. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

BHA54223 Axle / Spindle Nut Torque Specification
  1. step : Removing the Wheel (0:50)
    • Pry off the center cap with a pick
    • Loosen the 35mm axle nut
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
    • If the wheel is stuck, thread on one lug nut on a couple of threads
    • Strike the rear of the tire with a rubber mallet
    • Remove the placeholder lug nut
    • Pull off the wheel
  2. step : Removing the Brake Pads (2:31)
    • Hold the wheel studs with a brake rotor
    • Remove the T30 Torx screw from the brake rotor
    • Remove the two 14mm bolts from the caliper bracket
    • Pull the caliper off
    • Put the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (4:03)
    • Remove the two 15mm bolts from the caliper bracket
    • Pull off the brake caliper bracket
    • Pry the rubber plug out of the brake rotor
    • Put the rubber plug aside
    • Loosen the emergency brake adjuster as needed
    • Strike the drum surface of the rotor with a hammer to loosen the rotor
    • Pull the rotor off
    • Clean the hub surface with a wire brush
  4. step : Removing the Hub (6:08)
    • Disconnect the ABS sensor wiring harness
    • Remove the axle nut
    • Separate the axle from the hub with a hammer and punch
    • Put paper towel between the hub and the emergency brake
    • Apply rust penetrant to the hub bolts
    • Remove the four 13mm bolts from the hub
    • Push the axle out of the hub
    • Pull off the hub and backing plate
    • Push the ABS sensor harness through the backing plate
    • Hang the backing plate on the wheel spindle
  5. step : Installing the Hub (10:42)
    • Push the ABS sensor wire through the backing plate
    • Push the rubber ABS sensor boot into place
    • Put the hub into place
    • Set the axle into the hub
    • Start the axle nut by hand
    • Start the four 13mm bolts for the hub
    • Tighten the four 13mm bolts to 52 foot-pounds of torque
    • Connect the ABS sensor wiring harness
  6. step : Preparing the New Brake Pads and Rotors (11:59)
    • Pry off the brake pad shims with a flat blade screwdriver
    • Clean the brake pad shims with a wire brush
    • Clean the caliper bracket with a wire brush
    • Apply brake grease to the shim-mounting area of the caliper bracket
    • Place the shim onto the caliper bracket
    • Apply grease to the caliper shims
    • Pull out the caliper slides
    • Apply grease to the caliper slides
    • Push the caliper slide into the caliper
  7. step : Installing the Brake Rotor (15:08)
    • Apply grease to the hub surface
    • Put the rotor onto the hub backwards
    • Spray the rear of the hub with brake cleaner
    • Pull off the brake rotor
    • Slide the brake rotor on
    • Spray the front of the rotor with brake cleaner
    • Insert the T30 Torx bolt into the rotor
    • Set the emergency brake adjuster with a flat blade screwdriver
    • Push the rubber plug into the brake rotor
    • Put the caliper bracket into place
    • Insert the two 15mm bolts into the caliper bracket
    • Tighten the two 15mm bolts to 89 foot-pounds of torque
  8. step : Installing the Brake Pads (17:05)
    • Put the brake pads into the caliper bracket
    • Apply grease to the back of the brake pads
    • Push back the caliper piston with grove lock pliers
    • Put the brake caliper into place
    • Insert the two 14mm bolts into the caliper
    • Tighten the two 14mm bolts to 24 foot-pounds of torque
  9. step : Installing the Wheel (18:09)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the axle nut to 151 foot-pounds
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Rubber Mallet
  • Center Punch
  • Large Hammer
  • Pick
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Paper Towels
  • Brake Parts Cleaner
  • Gloves

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Torx Drivers & Sockets

  • T30 Torx Bit

5.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
3
0
0
0
0
Customer Service
I just wanted to take this opportunity to express how pleased I am with 1AAuto's customer service department. My words do not do it justice! All I can say is "unbelievably outstanding" customer service. I had an issue with shipping and they resolved it without any hesitation or what I like to call "no drama". They went beyond my expectation!

I recommend to anyone who is in the need to purchase auto parts that look no further than 1AAuto. You will not be disappointed!
August 31, 2017
Purchased
6 months ago
Fit well , great Shipping
Good service w8th great phone contact. I will order more when parts needed
July 5, 2017
Purchased
8 months ago
Hubs bearing
I loved the quality of my part ordered and the price. I highly recommend 1A auto too all my customers and friends. The price, quality of the part and the price was remarkable. I have ordered numerous parts from 1A and everytime its been wonderful doing business with them.... Keep up the great service please. Thank you
March 27, 2017
Purchased
11 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(18:52 min)

Tools List:

    General Tools

  • Jack Stands
  • Rubber Mallet
  • Center Punch
  • Large Hammer
  • Pick
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Paper Towels
  • Brake Parts Cleaner
  • Gloves

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Torx Drivers & Sockets

  • T30 Torx Bit



This part replaces:

  • Hollander 538-00124
  • Hollander 538-50221
  • OE # 19151003
  • OE # 19206600
  • OE # 4340278J01
  • TRQ BHA53476

Vehicle Fit

  • 2012-2015 Chevy Captiva Sport Rear Wheel Bearing & Hub Assembly Pair TRQ
  • 2007-2009 Chevy Equinox Rear Wheel Bearing & Hub Assembly Pair TRQ
  • 2007-2009 Pontiac Torrent Rear Wheel Bearing & Hub Assembly Pair TRQ
  • 2008-2010 Saturn Vue Rear Wheel Bearing & Hub Assembly Pair TRQ
  • 2007-2009 Suzuki XL-7 Rear Wheel Bearing & Hub Assembly Pair TRQ
Part #: 1ASHS00332

Ships Same Day for orders placed by 4 P.M. ET

TRQ
Brand #: BHA53476

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More