Replaces

Wheel Bearing & Hub Assembly Pair Timken 513121 - TKSHS00578

TIMKEN WHEEL BEARING & HUB ASSEMBLIES: 513121

Specifications:

  • Brand New Timken Hub Assemblies
  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) REAR
  • Direct replacements
  • Wheel studs already included and installed
  • Replaces dealer part numbers: 7470017, 7470105, 7470143, 7470567, 7470568, 12429204
  • Has ABS sensor w/stainless steel sensor wire clip
  • Built to strict quality control standards
  • For AWD (All Wheel Drive) models only

 

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Part Details

  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the wheel and tire (1:30)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Remove Caliper (2:00)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 15mm socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
  3. step : Remove brake disk (2:44)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (2:56)
    • Remove the 3 bolts securing the hub using your 13mm socket and 3/8 extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a rubber mallet to break it free, and work around the flange with the hammer to pull it off.
    • Leave the top 13mm loosely still in to prevent the hub from flying out if you hit it too hard.
    • Remove the hub, using driving tools to help work it out of the steering knuckle.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (8:30)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Watch part 2 to install your new 1A Auto hub!

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 19mm Socket
  • 32mm Socket
  • 35mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2002-2006Buick Rendezvous Buick Rendezvous All Wheel Drive Rear Wheel Bearing & Hub Assembly Pair Timken 513121
2002-2005Chevy Venture Chevy Venture All Wheel Drive Rear Wheel Bearing & Hub Assembly Pair Timken 513121
2002-2004Oldsmobile Silhouette Olds Silhouette All Wheel Drive Rear Wheel Bearing & Hub Assembly Pair Timken 513121
2001-2005Pontiac Aztek Pontiac Aztek All Wheel Drive Rear Wheel Bearing & Hub Assembly Pair Timken 513121
2002-2004Pontiac Montana Pontiac Montana All Wheel Drive Rear Wheel Bearing & Hub Assembly Pair Timken 513121
2005Pontiac Montana Pontiac Montana Base Model with All Wheel Drive Rear Wheel Bearing & Hub Assembly Pair Timken 513121

This part replaces:

  • Timken 513121
Only 4 left in stock
Part #: TKSHS00578


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: 513121

How-to Video:

(09:37 min)