Replaces

Wheel Bearing & Hub Assembly Pair Front TRQ BHA84992 - 1ASHS01201

Precision Engineered:

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.
100% Factory tested to precise OEM tolerances.

Highest Quality Materials:

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement:

Guaranteed to fit and function correctly for your specific application.

Part Details

  • Front or Rear Location: Front
  • Quantity: Pair
  • Includes: (1) 36mm Axle Nut Socket

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:52)
    • Loosen the lug nut covers with a 22mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Caliper Bracket (1:17)
    • Remove the T55 Torx bolts from the caliper
    • Use either a C-clamp to squeeze the caliper to push the caliper piston in
    • Remove the caliper
    • Pry the brake pads off with a flat blade screwdriver
    • Use a piece of pipe and ratchet to remove two 18mm bolts from the caliper bracket
    • Slide the rotor off
  3. For the third step, if you do not have air tools you can either loosen the center hub nut before you take your brakes apart by having somebody hold the brakes, or you can use a large bar, put it between the lug studs to hold it, and break the bar.

  4. step : Removing the Hub (2:58)
    • Disconnect the ABS harness from the frame and steering spindle by removing the clips
    • Pry off the center hub cap using a flat blade screw driver and hammer
    • Remove the center hub nut with an impact wrench and air blow gun
    • Remove the three 15mm hub bolts with two 15mm wrenches
    • Twist the hub nut a quarter of the way
    • And hammer from the back of the hub
    • Remove the hub nut and pull the hub out
  5. step : Installing the New Hub (5:06)
    • Place the backing plate onto the hub
    • Push the hub back into place
    • Insert and tighten the 15mm hub bolts
    • Torque the 15mm hub bolts to 75 ft/lbs
    • Remove the clip and feed the ABS harness back into place
    • Replace the clips and brackets to the ABS harness
    • Replace center hub nut and washer
    • Tighten the center hub nut
  6. step : Replacing the Caliper Bracket (6:46)
    • Place the rotor on the hub
    • Twist a lug nut to hold the rotor in place
    • Put the caliper on
    • Replace and tighten the 18mm bolts
    • Torque the 18mm bolts to 75 ft/lbs
    • Install the new brake pads into the bracket, tapping lightly with a hammer
    • Grease the caliper bolts
    • Place the caliper onto the bracket
    • Replace and tighten the T55 Torx bolts
    • Torque the bolts to 30 ft/lbs
  7. step : Reinstalling the Wheel (8:46)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the 22mm bolts
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the center hub nut to a 125 ft/lbs
    • Reattach the center cap
  8. step : Testing the Brakes (9:33)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    Allen Wrenches

  • 5mm Allen Wrench

  • General Tools

  • Hammer
  • Jack Stands
  • Large C-Clamp

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 18mm Socket
  • 22mm Socket
  • 35mm Socket

  • Torx Drivers & Sockets

  • T55 Torx Socket

  • Wrenches - Metric

  • 15mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1997Chevy Blazer S10 Chevy Blazer S10 All Wheel Drive Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ
1998-2005Chevy Blazer S10 Chevy Blazer S10 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ
1998-2004Chevy S10 Pickup Chevy S10 Pickup 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ
1998-2000GMC Envoy GMC Envoy Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ
1997GMC Jimmy S-15 GMC Jimmy S-15 All Wheel Drive Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ
1998-2001GMC Jimmy S-15 GMC Jimmy S-15 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ
1998-2004GMC S-15 Sonoma GMC S-15 Sonoma 4 Wheel Drive Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ
1998-2000Isuzu Hombre Isuzu Hombre Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ
1997-2001Oldsmobile Bravada Olds Bravada Front Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ

This part replaces:

  • TRQ BHA84992
Part #: 1ASHS01201


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA84992

How-to Video:

(10:03 min)