Replaces

Wheel Bearing & Hub Assembly Front TRQ BHA84979 - 1ASHS01184

Precision Engineered

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application.

Part Details

  • Front or Rear Location: Front
  • Includes: (1) 34mm Axle Nut Socket

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:43)
    • Loosen the lug nut covers with a 19mm socket
    • Loosen the hub nut with a 35mm socket and a pipe for leverage
    • Leave the hub nut on for a few threads
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Caliper and Rotor (1:45)
    • Remove the hub nut
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove the 15mm bolts from the brake caliper
    • Pull the caliper up and off
    • Remove the 15mm bolts from the caliper bracket
    • Remove the caliper bracket
    • Remove the rotor
  3. When removing the 13mm bolts from the hub, do not damage the boot on the CV axle

  4. step : Removing the Hub (2:41)
    • Remove the three 13mm bolts on the back of the hub
    • Hammer on the side of the hub
    • Pull the hub off
  5. step : Installing the New Hub (3:30)
    • Put a 13mm bolt on the hub bracket
    • Insert the hub into place
    • Insert and tighten the 13mm bolts to the hub
    • Torque the 13mm bolts to 65 ft/lbs
  6. step : Installing the Rotor and Brake Caliper (4:28)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Put the bracket back into place
    • Start the 15mm bolts by hand and tighten them
    • Tighten the bolts to 85 ft/lbs of torque
    • Install the new brake pads into the bracket
    • Apply grease to the brake pad tabs
    • Insert the brake pad slides
    • Put the caliper on
    • Tighten the bolts to 75 foot-pounds
    • Replace the hub nut cap preliminarily
  7. step : Reattaching the Wheel (6:37)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the hub nut to 159 ft/lbs
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket
  8. step : Testing the Brakes (7:35)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Brake Fluid

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket
  • 19mm Socket
  • 35mm Socket

3.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
0
1
0
0
Only one came.
Ordered two wheel bearings with socket but, only one bearing and socket came. So had to call back so they could send the other one. I was pressed for time but, they did get it to me in two days.
May 15, 2018
Purchased
2 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2003-2004 Buick Century without ABS Brakes (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2002-2004 Buick Regal without ABS Brakes (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2003-2005 Buick Rendezvous without ABS Brakes (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2000-2005 Chevy Impala without ABS Brakes (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2000-2005 Chevy Monte Carlo without ABS Brakes (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2003-2005 Chevy Venture without ABS Brakes Front Wheel Drive (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2003-2005 Pontiac Aztek without ABS Brakes (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2003 Pontiac Grand Prix without ABS Brakes (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2003-2004 Pontiac Montana without ABS Brakes Front Wheel Drive (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ
  • 2005 Pontiac Montana without ABS Brakes (1) 34mm Axle Nut Socket Wheel Bearing & Hub Assembly Front with TRQ

This part replaces:

  • TRQ BHA84979
Part #: 1ASHS01184

TRQ
Brand #: BHA84979

How-to Video:

(08:03 min)