Replaces

Wheel Bearing & Hub Assembly TRQ BHA84975 - 1ASHS01177

Precision Engineered

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application.

Part Details

  • Includes: (1) 32mm Axle Nut Socket

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:31)
    • Loosen the lug nuts on the wheel.
    • Jack the car up.
    • Remove the lug nuts and the wheel.
    • If it won't move, put a couple lug nuts on partially and hit the top of the wheel to break it free. Then remove the lug nuts and pull the wheel off.
    • Pry out the hub nut cotter pin
    • Remove the hub nut with a 32mm socket and breaker bar
    • Tap the axle out of the hub with a hammer
  2. step : Removing the Brake Caliper (2:45)
    • Check the rotor. If the rotor is rough it needs to be replaced.
    • Turn the wheel.
    • Remove the two bolts from the back of the caliper using a T45 Torx bit or Allen bit.
    • Place a screwdriver into the hole on the side of the caliper. Pry the caliper.
    • Pry off the bracket to remove the caliper.
    • Remove the inner brake shoe.
    • Wire tie the caliper up.
  3. step : Remove the Rotor (5:09)
    • Remove the two 21mm bolts from the back of the bracket using a breaker bar or pipe for leverage.
    • Slide the bracket off.
    • Remove the locks around the bolts if they are there.
    • Coat the disk with penetrating oil.
    • Partially replace a couple lug nuts and hit the disk to break it free.
    • Remove the lug nuts and disk.
  4. step : Removing the Hub (6:41)
    • Remove the hub nut if you have not already done so
    • Remove the four 15mm bolts from the hub
    • Remove the 10mm bolt from the ABS sensor
    • Tap the hub loose with a hammer
    • Pull off the hub
    • Clean the steering knuckle with a wire brush
  5. step : Installing the Hub (8:56)
    • Put the hub into place
    • Insert the four 15mm bolts in the hub
    • Tighten the bolts to 45 foot-pounds of torque
    • Thread on the hub nut
    • Tighten the hub nut preliminarily
    • Connect the ABS sensor
    • Insert the 10mm bolt for the ABS sensor
  6. step : Replacing the Front Brakes (10:33)
    • Slide the rotor into place.
    • Put the bracket onto the rotor.
    • Secure it with the two bolts.
    • Tighten to 120 foot-pounds
    • Clip the wire ties and pull the caliper down.
    • Put the old pad back in to the caliper and tighten with a C-Clamp to push the piston back in.
    • Put the pads into place with the clips to secure them.
    • Put the caliper into place on the rotor.
    • Slide the bracket into the caliper.
    • Place the bolts onto the back and tighten to 30 foot-pounds
  7. step : Replacing the Wheels (13:47)
    • Remove the lug nuts.
    • Tighten the hub nut to the manufacturer's recommended torque setting
    • Put the wheel back into place.
    • Replace the lug nuts and tighten them in a star pattern.
    • Put the car on the ground and tighten the lug nuts to 100 foot-pounds in a star pattern
  8. step : Testing the Brakes (14:09)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    Allen Wrenches

  • 8mm Allen Wrench

  • General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • 3/8 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 15mm Socket
  • 19mm Socket
  • 21mm Socket
  • 32mm Socket

  • Torx Drivers & Sockets

  • T45 Torx Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1996-2007 Chrysler Town & Country Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 2000-2003 Chrysler Voyager Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 1996-2000 Dodge Caravan with 15 Inch or 16 Inch Wheels Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 2001-2007 Dodge Caravan Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 1996-2000 Dodge Grand Caravan with 15 Inch or 16 Inch Wheels Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 2001-2007 Dodge Grand Caravan Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 1996-2000 Plymouth Grand Voyager with 15 Inch or 16 Inch Wheels Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 1997 Plymouth Prowler Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 1999-2001 Plymouth Prowler Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ
  • 1996-2000 Plymouth Voyager with 15 Inch or 16 Inch Wheels Front Wheel Bearing & Hub Assembly (1) 32mm Axle Nut Socket TRQ

This part replaces:

  • TRQ BHA84975
Only 3 left in stock
Part #: 1ASHS01177

TRQ
Brand #: BHA84975

How-to Video:

(14:34 min)