Replaces

Wheel Bearing & Hub Assembly Front TRQ BHA54059 - 1ASHF00357

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
      Direct Fit Replacement
      Precision Engineered
      Highest Quality Materials
  • Bearing Type:   Ball Bearing
  • Front or Rear Location:   Front

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Fits LH (Driver Side) or RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 19206599, 4342178J01, 4342178J00, 43421 78J01, 43421 78J00
  • 3 Bolt Flange
  • Fits 5 Lug Wheels
  • New wheel studs installed
  • Direct replacement
  • Built to strict quality control standards

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA54059 Axle / Spindle Nut Torque Specification

  1. step : Removing the Wheel (0:52)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Axle Nut (1:22)
    • Insert a wrench onto a spline, angled toward the inside of the vehicle
    • Thread a lug nut over the wrench
    • Rotate the hub so the wrench is pressed to the caliper
    • Remove the T30 Torx bolt
    • Lower the vehicle to the ground
    • Remove the 35mm axle nut
    • Raise the vehicle
    • Remove the wrench and lug nuts
    • Insert a flat punch into the divet in the center of the axle
    • Hammer the punch to tap the splines free
  3. step : Removing the Caliper Bracket (3:31)
    • Remove the two 18mm bolts from the caliper bracket
    • Pull the caliper off
    • Put the caliper aside
    • Remove the rotor
  4. step : Removing the Hub Assembly (4:28)
    • Clean off the hub with a wire brush and rust penetrant
    • Disconnect the ABS sensor connector
    • Remove the 15mm bolts from the back of the hub
    • Remove the wheel hub and bearing
  5. step : Installing the Hub Assembly (8:20)
    • Clean off any build up and debris from the hub surface with a wire brush
    • Insert the wheel hub into the spindle
    • Tighten the 15mm bolts
    • Torque the bolts to 96 foot-pounds
    • Reconnect the ABS sensor
  6. step : Installing the Brake Rotor (10:52)
    • Apply grease to the hub surface
    • Put the rotor onto the hub backwards
    • Spray the rear of the hub with brake cleaner
    • Pull off the brake rotor
    • Slide the brake rotor on
    • Spray the front of the rotor with brake cleaner
    • Put the caliper bracket into place
    • Insert the two 18mm bolts into the caliper bracket
    • Tighten the two 18mm bolts to 137 foot-pounds of torque
  7. step : Reinstalling the Axle Nut (11:55)
    • Insert a wrench onto a spline, angled toward the inside of the vehicle
    • Thread a lug nut over the wrench
    • Rotate the hub so the wrench is pressed to the caliper
    • Tighten the axle nut with a 35mm socket and ratchet
    • Torque the nut to 151 foot-pounds
    • Pop out the center cap on the wheel
  8. step : Reattaching the Wheel (12:41)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Seize Grease
  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 35mm Socket
  • Complete Metric Socket Set

  • Torx Drivers & Sockets

  • T30 Torx Bit

  • Wrenches - Metric

  • Complete Metric Wrench Set

4.83/ 5.0
6 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
5
1
0
0
0
As usual. Fair price. Fast delivery. Great service.
1A Auto is where I look first when Im looking for automotive parts. Their prices are almost always either better or at least competitive AND shipping is free. Their products are good quality and they stand behind them. Their customer service, when Ive needed them, is as good as all the rest. Whats not to like?
February 2, 2017
Works well & I saved a bunch
I was a bit leary of buying these, but it assembled properly and is quiet. The youtube video was very helpful. I would do it again.
June 22, 2017
08 Suzuki XL7 front wheel bearing part replaced successful
Per notation above, with the arrival of purchased part & learning how to Rmv/Install the new part, by myself with the right tools, I was able to have the Suzuki up and running in no time. Thanks 1AAuto for the service rendered... J Medrana-customer in VaBeach.
July 20, 2017
Amazing Equipment
The parts were exactly what you said they were. They worked perfectly!!!
August 12, 2017
Thank you 1A auto.Good price and fast shipping. will be ordering here again.
June 11, 2018
Bearing review
I recently purchased this bearing and hub assembly for my 2007 Pontiac torrent. It was an easy installation. Everything lined up correctly and the parts were smooth operating. They were shipped to my door a lot sooner than expected. I will be doing business win 1aauto in the future.
September 14, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Are the bearings already in the hub or do they need to be pressed in?
Randy R September 24, 2016
They are already in the hub.
Timothy H September 24, 2016
They are already in the hub
Eric S September 24, 2016
The bearings are already pressed into the hub assembly. So no need to do anything other than install the hub assembly.
Martin R September 24, 2016
all pre-assembled. No pressing needed
Brian F September 26, 2016
This a complete assembled unit, with bearings and seals installed. No need to do anything. Take the old unit out and put the new unit in. Jim B.
Jim B September 27, 2016
Randy, this is a sealed assy so the bearings are already in the hub; no need for them to be pressed in.
Laurie C October 3, 2016
it is a complete unit. no need to press in bearings. ready to install
Robert S June 11, 2018
Year Make Model Description
2007-2009Chevy Equinox Chevy Equinox Front Wheel Bearing & Hub Assembly TRQ
2007-2009Pontiac Torrent Pontiac Torrent Front Wheel Bearing & Hub Assembly TRQ
2008-2010Saturn Vue Saturn Vue Front Wheel Bearing & Hub Assembly TRQ
2007-2009Suzuki XL-7 Suzuki XL-7 Front Wheel Bearing & Hub Assembly TRQ
Part #: 1ASHF00357


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA54059

How-to Video:

(13:16 min)