Replaces

Wheel Bearing & Hub Assembly Front TRQ BHA53939 - 1ASHF00069

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
    Direct Fit Replacement
    Precision Engineered
    Highest Quality Materials
  • Bearing Type: Ball Bearing
  • Front or Rear Location: Front

Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • 3 bolt flange
  • Direct replacement
  • Replaces dealer part numbers: 7467558, 12413005, 12413006, 12413139
  • Fits 5 lug wheel
  • Wheel studs already installed
  • Correct for vehicles WITHOUT front wheel ABS

 

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA53939 Axle / Spindle Nut Torque Specification

  1. step : Removing the Wheel (0:43)
    • Loosen the lug nut covers with a 19mm socket
    • Loosen the hub nut with a 35mm socket and a pipe for leverage
    • Leave the hub nut on for a few threads
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Caliper and Rotor (1:45)
    • Remove the hub nut
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove the 15mm bolts from the brake caliper
    • Pull the caliper up and off
    • Remove the 15mm bolts from the caliper bracket
    • Remove the caliper bracket
    • Remove the rotor
  3. When removing the 13mm bolts from the hub, do not damage the boot on the CV axle

  4. step : Removing the Hub (2:41)
    • Remove the three 13mm bolts on the back of the hub
    • Hammer on the side of the hub
    • Pull the hub off
  5. step : Installing the New Hub (3:30)
    • Put a 13mm bolt on the hub bracket
    • Insert the hub into place
    • Insert and tighten the 13mm bolts to the hub
    • Torque the 13mm bolts to 65 ft/lbs
  6. step : Installing the Rotor and Brake Caliper (4:28)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Put the bracket back into place
    • Start the 15mm bolts by hand and tighten them
    • Tighten the bolts to 85 ft/lbs of torque
    • Install the new brake pads into the bracket
    • Apply grease to the brake pad tabs
    • Insert the brake pad slides
    • Put the caliper on
    • Tighten the bolts to 75 foot-pounds
    • Replace the hub nut cap preliminarily
  7. step : Reattaching the Wheel (6:37)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the hub nut to 159 ft/lbs
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket
  8. step : Testing the Brakes (7:35)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Brake Fluid

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket
  • 19mm Socket
  • 35mm Socket

5.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
0
Wheel bearing for my Monte Carlo
I Write to say thank you 1aauto for the fast shipping!! Also I have been in the industry since I was 8yrs old and know a quality part when I see one. After reviewing it I can say that the quality was as equal to the big box parts stores and at a much better price!! And fit with no issues at all!! Thanks again 1aauto from Elmer Lurz
September 22, 2018
Purchased
1 month ago
No Problems
Works as expected so far no problems. Good price and quick shipping.
July 15, 2017
Purchased
1 year ago
2000 Impala
Part came fast and well packed. Fit just like the original and will probably buy from again in the near future. Thanks again.
July 8, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2003-2004Buick Century Buick Century without ABS Brakes Wheel Bearing & Hub Assembly Front TRQ
2002-2004Buick Regal Buick Regal without ABS Brakes Wheel Bearing & Hub Assembly Front TRQ
2003-2005Buick Rendezvous Buick Rendezvous without ABS Brakes Wheel Bearing & Hub Assembly Front TRQ
2000-2005Chevy Impala Chevy Impala without ABS Brakes Wheel Bearing & Hub Assembly Front TRQ
2000-2005Chevy Monte Carlo Chevy Monte Carlo without ABS Brakes Wheel Bearing & Hub Assembly Front TRQ
2003-2005Chevy Venture Chevy Venture without ABS Brakes Front Wheel Drive Wheel Bearing & Hub Assembly Front TRQ
2003-2005Pontiac Aztek Pontiac Aztek without ABS Brakes Wheel Bearing & Hub Assembly Front TRQ
2003Pontiac Grand Prix Pontiac Grand Prix without ABS Brakes Wheel Bearing & Hub Assembly Front TRQ
2003-2004Pontiac Montana Pontiac Montana without ABS Brakes Front Wheel Drive Wheel Bearing & Hub Assembly Front TRQ
2005Pontiac Montana Pontiac Montana without ABS Brakes Wheel Bearing & Hub Assembly Front TRQ

This part replaces:

  • Hollander 538-01527
  • TRQ BHA53939
  • OE # 88964096
Part #: 1ASHF00069


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA53939

How-to Video:

(08:03 min)