Replaces

Wheel Bearing & Hub Assembly Front Timken SP450201 - TKSHF00100

TIMKEN WHEEL BEARING & HUB ASSEMBLY: SP450201

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Fits 5 Lug Wheel
  • Replaces dealer part numbers: YL5Z-1104-AA, 1F02-33-061, YL5Z1104AA, 1F0233061
  • New wheel studs installed
  • Direct replacement
  • Built to strict quality control standards
  • Fits models without Pulse Vacuum Hubs
  • Fits models with 4 Wheel ABS (Anti-Lock Brakes) only
  • Fits 4WD (Four Wheel Drive) Models only
Note: This hub only fits 4wd vehicles that have 4 wheel ABS and non pulse vacuum hubs. To tell the difference, the non pulse hub assy will have a smooth, inner surface (as pointed out in picture) where the axle shaft comes through.

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Part Details

  • Front or Rear Location: Front

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:51)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 32mm axle nut
    • Remove the wheel lock lug nut with a wheel lock key
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub (1:55)
    • Remove the two 15mm bolts holding the caliper bracket to the spindle
    • Secure the caliper bracket and assembly out of the way with a bungee cord
    • Remove the rotor
    • Disconnect the ABS sensor
    • Pry the ABS sensor connectors from the frame
    • Remove the 8mm bolt from the ABS harness
    • Remove the 32mm axle nut
    • Lightly tap the end of the axle with a hammer
    • Remove the three 15mm bolts on the backside of the spindle
    • Release the hub with a chisel and hammer and separate it from the spindle
  3. step : Installing the Hub (6:00)
    • Insert the hub and sensor into the spindle
    • Start the three 15mm bolts
    • Tighten the three 15mm bolts to the hub
    • Torque the 15mm bolt to 85 foot-pounds
    • Reinstall the 32mm axle nut by hand
    • Tighten the 8mm bolt to the ABS harness
    • Clip in the harness along the frame
    • Connect the ABS harness
    • Reinstall the rotor
    • Insert the caliper into place
    • Tighten the two 15mm bolts to the caliper
    • Torque the caliper bolts to 85 foot-pounds
  4. step : Reattaching the Wheel (8:11)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds of torque in a crossing or star pattern
    • Tighten the 32mm axle nut
    • Torque the axle nut to 162 foot-pounds
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Chisel
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 15mm Socket
  • 8mm Socket

  • Specialty Tools

  • Trim Tool Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2000 Ford Ranger 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes without Pulse Vacuum Hubs without Hub Lockout Splines Timken SP450201
  • 2001-2002 Ford Ranger 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Timken SP450201
  • 1999-2000 Mazda B3000 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes without Pulse Vacuum Hubs without Hub Lockout Splines Timken SP450201
  • 2001-2002 Mazda B3000 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Timken SP450201
  • 1999-2000 Mazda B4000 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes without Pulse Vacuum Hubs without Hub Lockout Splines Timken SP450201
  • 2001-2003 Mazda B4000 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Timken SP450201

This part replaces:

  • Timken SP450201
  • OE # 1F0233061
  • Hollander 538-01570
Only 4 left in stock
Part #: TKSHF00100

Timken
Brand #: SP450201

How-to Video:

(09:11 min)