Replaces

Wheel Bearing & Hub Assembly Front Timken HA590069 - TKSHF00166

Part Details

  • Front or Rear Location: Front

TIMKEN WHEEL BEARING & HUB ASSEMBLY: HA590069

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 22701520
  • New wheel studs installed
  • Fits 4 Lug Wheel
  • Direct replacement
  • Built to strict quality control standards
  • Fits models without ABS (Anti-Lock Brakes)

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:04)
    • Loosen the caps and remove the wheel cover.
    • Remove the 30mm lug nut in the center of the wheel.
    • Loosen the other lug nuts.
    • Jack the car up and remove the lug nuts.
    • Pull the wheel off.
  2. step : Removing the Brakes (1:49)
    • Using a screwdriver pry the caliper from the rotor.
    • Remove the two 14mm bolts on the back of the caliper.
    • Pull the caliper off and set it aside.
    • Pry the pads off.
    • Remove the two 15mm bolts securing the caliper bracket (Use breaker bar or pipe for leverage).
    • Remove the caliper bracket.
    • Remove the rotor.
  3. step : Removing the Hub (3:10)
    • If the axel doesn't just push out hit it once with a hammer.
    • Remove the three bolts securing the hub.
    • Disconnect ABS harness if the vehicle has this.
    • Hit the side of the hub with a hammer to loosen it up.
    • Pull the hub free.
  4. step : Replacing the Hub (5:11)
    • Line the new hub with the back plate.
    • Reconnect the ABS harness if the vehicle has this.
    • Replace the three bolts that secure the hub. 70 – 75ft/lbs.
    • Replace the washer and nut on the hub.
  5. step : Replacing the Brakes (7:00)
    • Put the rotor in place and hold it on with one lug nut.
    • Put the caliper bracket back into place.
    • Replace the caliper bolts. 75 – 80 ft/lbs.
    • Put the brake pads back into place.
    • Replace the caliper and caliper bolts. Tighten to 20 – 22ft/lbs.
  6. step : Replace the Wheels (7:43)
    • Remove the lug nut.
    • Put the wheel into place.
    • Replace the lug nuts.
    • Lower the vehicle and tighten the lug nuts to 100ft/lbs.
    • Tighten the center nut to 155ft/lbs.
    • Replace the hub cap if this applies.
  7. step : Prepare the Brakes (8:37)
    • Pump the Brakes until they are firm before road testing.
    • Test stop from 5 then 10 mph.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer

  • Ratchets & Related

  • Socket Extensions
  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 15mm Socket
  • 30mm Socket
  • 18mm Socket
  • 16mm Socket
  • 17mm Socket
  • 14mm Socket
  • 19mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2005-2010Chevy Cobalt Chevy Cobalt Front for Models with 4 Lug Wheels Wheel Bearing & Hub Assembly without ABS Brakes Timken HA590069
2007-2009Pontiac G5 Pontiac G5 Front for Models with 4 Lug Wheels Wheel Bearing & Hub Assembly without ABS Brakes Timken HA590069
2005-2006Pontiac Pursuit Pontiac Pursuit Front for Models with 4 Lug Wheels Wheel Bearing & Hub Assembly without ABS Brakes Timken HA590069
2003Saturn Ion Saturn Ion Front Wheel Bearing & Hub Assembly without ABS Brakes Timken HA590069
2004-2007Saturn Ion Saturn Ion Front for Models with 4 Lug Wheels Wheel Bearing & Hub Assembly without ABS Brakes Timken HA590069

This part replaces:

  • Timken HA590069
  • Hollander 538-01602
  • OE # 22701520
Part #: TKSHF00166


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: HA590069

How-to Video:

(09:02 min)