Replaces

Wheel Bearing & Hub Assembly Front Pair Timken 515013 - TKSHS00324

Part Details

  • Quantity: Pair
  • Front or Rear Location: Front

TIMKEN WHEEL BEARING & HUB ASSEMBLIES: SP450201

These replacement hub & bearing assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assemblies
  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Fit 5 Lug Wheels
  • Replaces dealer part numbers: YL5Z-1104-AA, 1F02-33-061, YL5Z1104AA, 1F0233061
  • New wheel studs installed
  • Direct replacements
  • Built to strict quality control standards
  • Fit models without Pulse Vacuum Hubs
  • Fit models with 4 Wheel ABS (Anti-Lock Brakes) only
  • Fit 4WD (Four Wheel Drive) Models only

Note: These hubs only fit 4wd vehicles that have 4 wheel ABS and non pulse vacuum hubs. To tell the difference, the non pulse hub assemblies will have a smooth, inner surface (as pointed out in picture) where the axle shafts come through.

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:51)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 32mm axle nut
    • Remove the wheel lock lug nut with a wheel lock key
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub (1:55)
    • Remove the two 15mm bolts holding the caliper bracket to the spindle
    • Secure the caliper bracket and assembly out of the way with a bungee cord
    • Remove the rotor
    • Disconnect the ABS sensor
    • Pry the ABS sensor connectors from the frame
    • Remove the 8mm bolt from the ABS harness
    • Remove the 32mm axle nut
    • Lightly tap the end of the axle with a hammer
    • Remove the three 15mm bolts on the backside of the spindle
    • Release the hub with a chisel and hammer and separate it from the spindle
  3. step : Installing the Hub (6:00)
    • Insert the hub and sensor into the spindle
    • Start the three 15mm bolts
    • Tighten the three 15mm bolts to the hub
    • Torque the 15mm bolt to 85 foot-pounds
    • Reinstall the 32mm axle nut by hand
    • Tighten the 8mm bolt to the ABS harness
    • Clip in the harness along the frame
    • Connect the ABS harness
    • Reinstall the rotor
    • Insert the caliper into place
    • Tighten the two 15mm bolts to the caliper
    • Torque the caliper bolts to 85 foot-pounds
  4. step : Reattaching the Wheel (8:11)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds of torque in a crossing or star pattern
    • Tighten the 32mm axle nut
    • Torque the axle nut to 162 foot-pounds
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Chisel
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 15mm Socket
  • 8mm Socket

  • Specialty Tools

  • Trim Tool Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2000Ford Ranger Ford Ranger 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair without Pulse Vacuum Hubs without Hub Lockout Splines Timken 515013
2001-2002Ford Ranger Ford Ranger 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair Timken 515013
1999-2000Mazda B3000 Truck Mazda B3000 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair without Pulse Vacuum Hubs without Hub Lockout Splines Timken 515013
2001-2002Mazda B3000 Truck Mazda B3000 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair Timken 515013
1999-2000Mazda B4000 Truck Mazda B4000 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair without Pulse Vacuum Hubs without Hub Lockout Splines Timken 515013
2001-2003Mazda B4000 Truck Mazda B4000 Truck 4 Wheel Drive Front Wheel Bearing & Hub Assembly for Models with 4 Wheel ABS Brakes Pair Timken 515013

This part replaces:

  • Timken 515013
Only 2 left in stock
Part #: TKSHS00324


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: 515013

How-to Video:

(09:11 min)