Replaces

Wheel Bearing & Hub Assembly Front Pair Timken 513253 - TKSHS00394

TIMKEN WHEEL BEARING & HUB ASSEMBLIES: HA590106

These replacement hub & bearing assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assemblies
  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • 4 Bolt Flanges
  • Fit 5 Lug Wheels
  • Replaces dealer part numbers: 1T0 498 621, 3C0 498 621, 8J0 598 625, 1T0498621, 3C0498621, 8J0598625
  • Direct replacements
  • Built to strict quality control standards

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Part Details

  • Front or Rear Location: Front
  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:50)
    • Pry off the center cap with a flat blade screwdriver
    • Pry off the lug bolt covers with a pick
    • Loosen the 27mm hub bolt
    • Loosen the locking lug bolt with the key
    • Loosen the lug bolts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug bolts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:44)
    • Pry off the caliper bolt plugs by hand
    • Remove the two T47 Torx bolts from the brake caliper
    • Pry the caliper clip off with a flat blade screwdriver
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
  3. step : Removing the Brake Rotor (2:37)
    • Remove the two 21mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the T30 bolt from the rotor
    • Apply rust penetrant to the hub
    • Thread in one lug bolt
    • Strike the back of the rotor with a hammer to loosen it
    • Pull the rotor off
  4. step : Removing the Hub (3:33)
    • Remove the 27mm hub nut
    • Thread in the hub bolt half way
    • Strike the hub bolt with a hammer to loosen the axle
    • Remove the hub bolt
    • Remove the three 16mm nuts from the control arm
    • Pry down the control arm with a pry bar
    • Tap the axle out of the hub with a hammer and a socket
    • Remove the four 12-point 12mm bolts from the hub
    • Thread one 12mm bolt half way into the hub
    • Tap the hub with a hammer to loosen it
  5. step : Installing the Hub (5:20)
    • Put the hub into place
    • Insert the 12mm bolts into the hub
    • Tighten the 12mm bolts to 50 foot-pounds of torque
    • Turn each hub bolt an extra 1/4- turn
    • Push the axle into place
    • Push the control arm onto its studs
    • Fasten the three 16mm nuts onto the control arm
    • Tighten the three 16mm nuts to 50 foot-pounds
    • Thread on the hub bolt by hand
  6. step : Installing the Brake Rotor (7:06)
    • Slide the rotor on
    • Insert the T30 bolt into the rotor
    • Put the bracket back into place
    • Start the two 21mm bolts by hand
    • Tighten the 21mm bolts to 90 foot-pounds
  7. step : Installing the Brake Pads (8:01)
    • Put the brake pads into the caliper bracket if they are not already installed
    • Put the caliper on
    • Insert the two T47 bolts into the caliper
    • Tighten the T47 bolts to 30 foot-pounds
    • Push on the wire caliper bracket clip
    • Push on the caliper bolt plugs
  8. step : Reattaching the Wheel (8:44)
    • Slide the wheel into place
    • Start the lug bolts by hand
    • Tighten the lug bolts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug bolts to 100 foot-pounds in a crossing or star pattern
    • Push on the lug bolt caps
    • Tighten the hub bolts to 150 foot-pounds
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Pick
  • Jack Stands
  • Hammer
  • Floor Jack

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 21mm Socket
  • 27mm socket
  • 16mm Socket
  • 12mm 12-Point Socket
  • 17mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Does this bearing come with new bolts ?
Kenneth G on May 6, 2016
BEST ANSWER: none. You can reuse your wheel studs and hub flange bolts as needed

Vehicle Fit

Year Make Model Description
2006-2013Audi A3 Audi A3 Front Wheel Bearing & Hub Assembly Pair Timken 513253
2006-2013Audi A3 Quattro Audi A3 Quattro Front Wheel Bearing & Hub Assembly Pair Timken 513253
2015-2017Audi Q3 Audi Q3 Wheel Bearing & Hub Assembly Front Pair Timken 513253
2015-2017Audi Q3 Quattro Audi Q3 Quattro Wheel Bearing & Hub Assembly Front Pair Timken 513253
2008-2015Audi TT Audi TT Front Wheel Bearing & Hub Assembly Pair Timken 513253
2008-2015Audi TT Quattro Audi TT Quattro Front Wheel Bearing & Hub Assembly Pair Timken 513253
2012-2017Volkswagen Beetle VW Beetle Wheel Bearing & Hub Assembly Front Pair Timken 513253
2009-2017Volkswagen CC VW CC Front Wheel Bearing & Hub Assembly Pair Timken 513253
2007-2016Volkswagen Eos VW Eos Front Wheel Bearing & Hub Assembly Pair Timken 513253
2006-2014Volkswagen GTI VW GTI Front Wheel Bearing & Hub Assembly Pair Timken 513253
2011Volkswagen Golf VW Golf Front Wheel Bearing & Hub Assembly Pair (Built After 3/14/11 Production Date) Timken 513253
2012-2014Volkswagen Golf VW Golf Front Wheel Bearing & Hub Assembly Pair Timken 513253
2005-2006Volkswagen Jetta VW Jetta Front Wheel Bearing & Hub Assembly Pair (8th Vin Digit K) Timken 513253
2007-2017Volkswagen Jetta VW Jetta Front Wheel Bearing & Hub Assembly Pair Timken 513253
2006-2010Volkswagen Passat VW Passat Front Wheel Bearing & Hub Assembly Pair Timken 513253
2012-2017Volkswagen Passat VW Passat Wheel Bearing & Hub Assembly Front Pair Timken 513253
2008Volkswagen R32 VW R32 Front Wheel Bearing & Hub Assembly Pair Timken 513253
2006-2009Volkswagen Rabbit VW Rabbit Front Wheel Bearing & Hub Assembly Pair Timken 513253
2009-2017Volkswagen Tiguan VW Tiguan Front Wheel Bearing & Hub Assembly Pair Timken 513253

This part replaces:

  • Timken 513253
Only 1 left in stock
Part #: TKSHS00394


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: 513253

How-to Video:

(10:06 min)