Replaces
Frequently bought together
Part Details
TRQ ignition coils will have your engine running like new. TRQ ignition coils are manufactured to precise specifications using premium raw materials to optimize each vehicle's ignition system. To ensure peak performance, TRQ recommends replacing ignition coils in sets to prevent electrical output imbalances. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you an ignition coil replacement. This is a 2007 Audi A4, but the procedure is similar for many Audi models as well as engines. Items you will need for this are new ignition coils from 1AAuto.com, a T20 Torx driver and a flat blade screwdriver or, if you have one laying around, an Audi ignition coil puller.
Start out by opening the door and pulling the hood release lever. Then there's a safety latch. Pull up on the safety latch. Then there are two T20 Torx screws that hold the wiring harness. Remove those. Each coil has a little clip. You push down on the tab that's at the bottom of the harness connector. Some of them you'll hear a nice clicking sound and then pull the harness down off the coils. Use either the special Audi tool or you can just use a trusty screwdriver. Pry gently. Make sure you don't pry too much side to side. You want to pry straight up. Get the coil started and then twist it a little bit and pull it up and out.
The coil on the left is from 1A Auto. The original one is on the right, and you can see there's some cosmetic differences but the coils from 1A Auto are going to go in and replace and install just the same as your original.
Push the coil down in the same way as it came out, and obviously if you're going to replace all your coils you would just repeat this process for the other three, or five if you're doing it on a six cylinder. Then put the harness back up into place and push firmly, squeeze on the coil and the harness firmly to get it to lock into place. Then replace those two T20 screws. I just put it into place by hand first to make sure they get started correctly. Then tighten them up.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil on this 2004 Volkswagen Jetta with 1.8L engine. The items you'll need for this include a new ignition coil from 1AAuto.com, a Phillips screwdriver, and a flat blade screwdriver. For ignition coils 3 and 4, you'll need a 10mm socket and ratchet. For ignition coil 4, you'll also need a 5mm Allen bit.
First, we have to remove the engine cover by loosening these four Phillips clips. Just loosen it while pulling up on the engine cover, and then the engine cover pulls off and you can set it aside. For ignition coils 1 and 2, all you need is a flat blade screwdriver. Just press on the tab and pull the harness free, and then just pry the ignition coil up and out. Then, you just take your new ignition coil, push it down into place, and reconnect the harness.
To access ignition coil 3, you're going to have to remove the small air box. Just using a 10mm socket and ratchet, remove this 10mm nut and set the air box aside. To get to 4, you're also going to have to remove these three 5mm Allen bolts. We'll just fast-forward as Don removes those. Pull the bracket off and set it aside. Then just like before, push on the tab and pull the harness free. You may need to pry it to separate it, and then just pry the ignition coil up and out.
On the right is an old ignition coil; on the left is the new one from 1A Auto. You can see that they're identical, and they'll fit exactly the same. Take your new ignition coil, push it down into place, and then reconnect your harness. Replace the bracket and the three 5mm Allen bolts that hold it into place. We'll fast-forward as Don tightens those up.
Now, replace that small air box, the 10mm nut that holds it into place, and just tighten that up. Line up the four Phillips clips with these four holes. Just push the engine cover down into place and tighten up those four clips. You're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
