Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

This replacement Tail light is just what you need to get your vehicle in good looking form again!

This tail lamp features the following specifications:

  • LH (Driver Side) INNER
    • Mounts on trunk lid
  • Replaces dealer part numbers: 1HM 945 107, 1HM945107
  • Includes lens & Housing
  • DOT (Department of Transportation) & SAE (Society of Automotive Engineers) approved
  • Direct replacement
  • Correct for GL, GLS, & GT Models
    • Has amber top lens & red bottom lens
  • Will fit GLX & K2 Models, but look cosmetically different

This tail light makes a great replacement and has good cost savings over a dealer unit.



Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the tail light assembly (0:55)
    • Open the trunk
    • Peel back the trunk liner by removing four push clips.
    • Use your screwdriver to pry out the center of the clips to remove them.
    • Service the bulbs by unclipping the bracket holding the bulbs into the assembly and unplugging the bulbs
    • Unbolt the tail light assembly with an 8 mm socket and ratchet to remove the three nuts.
    • Remove your license plate and remove the four screws anchoring the plastic vanity piece behind the plate.
    • Unbolt the four nuts securing the tail lights to the vanity piece.
    • Pull the tail light assembly out.
  2. step : Install the new tail lights (6:33)
    • Secure the new tail lights to the plastic vanity piece with your 8 mm socket and ratchet.
    • Bolt the whole assembly back onto the car.
    • Plug in the bulbs and wiring harness bracket back into the tail lights.
    • Secure all six of the nuts securing the tail lights to the trunk.
    • Bolt the tail light assembly into place using your 8 mm socket and ratchet.
    • make sure your wiring harness and bulbs are all connected.
    • Replace the license plate.
    • Clip the trunk liner back into place and close the trunk.
    • Close the trunk and enjoy your new 1A Auto tail lights.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 8mm Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1993-1998Volkswagen Jetta VW Jetta GL Inner Tail Light Driver Side
1993-1998Volkswagen Jetta VW Jetta GLS Inner Tail Light Driver Side
1993-1998Volkswagen Jetta VW Jetta GT Inner Tail Light Driver Side
1999Volkswagen Jetta VW Jetta GL Inner Tail Light Driver Side (8th Vin Digit H)
1999Volkswagen Jetta VW Jetta GLS Inner Tail Light Driver Side (8th Vin Digit H)
Only 1 left in stock
Part #: 1ALTL01424

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(09:31 min)