Replaces
Volkswagen Headlight Pair - 1ALHP00492
1ALHP00492Frequently bought together
Part Details
- Quantity: Pair
- Light Option: Halogen
Specifications:
- Comes as a PAIR
- Fits both LH (Driver Side) & RH (Passenger Side)
- Replaces dealer part numbers: 1K6-941-005-S, 1K6-941-006-S, 1K6941005S, 1K6941006S
- Include lenses & housings
- Bulbs not included
- Fits models with halogen headlights only
- Not correct for models with HID (High Intensity Discharge) headlights
Direct fit replacement for OEM assembly
Trouble-free InstallationUses same wiring as original assembly. No cutting or splicing required.
DOT and SAE CompliantMeets federal regulations for on-road use
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.
Bulb Note:
These lights do not include bulbs. If you happen to receive a product with bulbs, the bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
-
step : Servicing the Bulbs (0:55)
- Twist the low beam cover counterclockwise
- Twist the bulb socket counterclockwise out of the light
- Pull the bulb off of the socket
- Push on the new bulb
- Twist the bulb clockwise into the light
- Twist on the low beam cover
- Remove the headlight cover
- Pull off the connector to disconnect it
- Push on the wire retainer and pull it up to remove it
- Pull the bulb off of the socket
- Push on the new bulb
- Put the tab down and lock the retainer in place
- Connect the harness
- Put the cover on
- If you are removing the headlights go to step 2
-
step : Removing the Grille (3:17)
- Remove the two clips on top of the grille with a Phillips screw
- Remove the two Phillips screws below the grille
- Push in the tabs on the top of the grille
- Pull up on either side of the grille
- Remove the grille
-
step : Loosening the Bumper Cover (4:05)
- Remove the T25 screw from the fender
- Remove the four T25 screws in the wheel well
- Repeat the process on the other side
- Remove the two T30 Torx screws on the top of the bumper
- Remove the series of T25 screws along the bottom of the bumper
-
step : Removing the Side Marker Light (5:10)
- Pry out the side marker light with a flat blade screwdriver
- Pull out the side marker light
- Twist the bulb socket out of the light
- Pull the bulb off of the socket
- Repeat the process on the other side
-
step : Removing the Bumper Cover (5:25)
- Pull off either end of the bumper cover
- Disconnect the side marker harness from the clip on either side
-
step : Removing the Headlight (5:35)
- Remove the T25 screws from the headlight bracket
- Disconnect the headlight wiring harness
- Pull the headlight out
-
step : Installing the New Headlight (5:57)
- Insert the headlight into place
- Reconnect the wiring harness to the headlight
- Replace the T25 screw on the top of the headlight bracket
-
step : Adjusting the Headlight (6:22)
- Park your car from 20 feet away on a level surface from a wall
- Adjust the headlight by turning the bolt on the inside of the headlight
- The light should concentrate an inch below where they sit on the car
- Tighten the T25 screws to the headlight
- Connect the headlight wiring harness
-
step : Tightening the Bumper Cover (7:13)
- Insert the bumper cover into place
- Tighten the two T30 screws to the top of the bumper
- Tighten the five T25 screws in the wheel well
- Clip the side marker light harness to the bumper on either side
-
step : Installing the Side Marker Light (7:59)
- Push the bulb socket into the light
- Push the side marker light into place, starting at the front
-
step : Reinstalling the Bumper Cover (8:10)
- Tighten the series of T25 screws along the bottom of the bumper
-
step : Reinstalling the Grille (8:14)
- Line up the tabs on the grille with the slots on the vehicle
- Push the grille into place
- Tighten the two Phillips screws below the grille
- Tighten the two clips on top of the grille with a Phillips screw
Tools needed for replacement:
- Phillips Head Screwdriver
- Flat Blade Screwdriver
- T25 Torx Driver
- T30 Torx Driver
Screwdrivers & Related
Torx Drivers & Sockets
Year | Make | Model | Description |
---|---|---|---|
2007-2009 | Volkswagen | GTI | VW GTI Halogen Headlight (8th Vin Digit K) Pair |
2006-2009 | Volkswagen | Golf | VW Golf Halogen Headlight (8th Vin Digit K) Pair |
2005 | Volkswagen | Jetta | VW Jetta Halogen Headlight (8th Vin Digit K) Pair |
2006-2010 | Volkswagen | Jetta | VW Jetta Sedan Halogen Headlight (8th Vin Digit K) Pair |
2009 | Volkswagen | Jetta | VW Jetta Wagon Halogen Headlight (8th Vin Digit K) Pair |
2006-2009 | Volkswagen | Rabbit | VW Rabbit Halogen Headlight Pair |