Replaces

Volkswagen Beetle Golf Jetta O2 Oxygen Sensor with Install Tool - 1AEEK00688

Specifications:

  • Direct Fit
    • Correct Connector No cutting or splicing
      • may appear different from original however will install and function correctly
    • Correct wire length (15 Inches)
  • Downstream Sensor as listed per applications
  • Heated
  • 4 wire configuration
  • 4 terminal configuration
  • Built and tested to strict quality control standards
  • Includes removal and installation tool

Note: For clarification purposes:

  • Upstream location is between the catalytic converter and the engine
  • Downstream location is between the catalytic converter and the tailpipe

If you have a bad O2 sensor causing your vehicle to run poorly or fail an emission test then this is the part for you.

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Downstream Oxygen Sensor (0:43)
    • Raise and secure the vehicle
    • Unbutton the O2 sensor insulation sleeve and pull it off
    • Remove the sensor wire from its bracket
    • Remove the two 10mm nuts from the sensor wire box
    • Pull the downstream O2 sensor wiring harness out of the box
    • Disconnect the downstream O2 sensor wiring harness
    • Put the O2 sensor tool onto the sensor wire and slide it onto the sensor
    • Put a 3/8 inch ratchet into the O2 sensor tool
    • Loosen the sensor until it can be twisted off by hand
    • Twist off the sensor by hand
  2. step : Installing the New Downstream Oxygen Sensor (2:28)
    • Twist the new O2 sensor into place
    • Tighten the new sensor with the O2 sensor tool and 3/8 inch ratchet
    • Button the insulation sleeve around the sensor wire
    • Clip the new sensor wire into its bracket
    • Reconnect the downstream O2 sensor wiring harness
    • Push the downstream O2 sensor wiring harness into the wiring harness box
    • Push the wiring harness box into place
    • Fasten the two 10mm nuts onto the wiring harness box
    • Lower the vehicle to the ground

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • 3/8 Inch Drive Ratchet
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • O2 Sensor Socket

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
0
0
0
0
Exactly what i needed
Perfect fit, can't beat the price. Socket worked like a charm.

So far, no issues with the O2 sensor.
September 5, 2017
Purchased
10 months ago
Great replacement
Bought this for my 2002 Beetle that had a code for the O2 sensor. I didn't know that this O2 sensor was different between engine sizes and had bought one from another retailer that turned out to be wrong (too long of a cable and didn't have the same mating connection). Returned that one and bought this one instead. It fits perfect and immediately cleared the code. No issues since install. Because of this, I now go to 1AAuto for most of my needs first, especially on parts like this where there are minor differences due to engine sizes hat other retailers don't mention.
February 12, 2017
Purchased
over 2 years ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2005 VW Beetle L4 2.0L (Engine ID AVH) (Engine ID AZG) Downstream O2 Oxygen Sensor with Install Tool
  • 2006-2010 VW Beetle L5 2.5L Rear Bank Downstream O2 Oxygen Sensor with Install Tool
  • 2000-2006 VW Golf L4 2.0L Downstream O2 Oxygen Sensor with Install Tool
  • 1999-2005 VW Jetta L4 2.0L Downstream O2 Oxygen Sensor with Install Tool

This part replaces:

  • OE # 06A906262BG
  • Standard Motor Products SG1170
Part #: 1AEEK00688

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(04:10 min)