Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Headlight Assembly on a 2000-06 Toyota Tundra
How to Replace Headlights and Bulbs 2000-04 Toyota Tundra
Created on:
Tools used
Tools used
Flat Blade Screwdriver
Phillips Head Screwdriver
Ratchet
10mm Socket
1. Change the bulbs
To just change the bulbs, pop the hood.
Reach behind the headlight assembly and unplug the bulb and disconnect the wiring harness.
You will have to pull a rubber boot out of the way to get at the bulb and unclip a wire clip.
2. Replace the head light assembly
Use a Phillips screwdriver and a flat blade screwdriver to remove the push clip at the top corner of the headlight assembly.
Pull the parking light out and disconnect the parking light.
Remove the bulb and transfer it to the new parking light assembly.
Unbolt the 10 mm bolt and three 10 mm nuts anchoring the headlight assembly.
Unplug the wiring harness and remove the bulbs and transfer them to the new headlight assembly.
3. Install the new headlight and parking light assemblies.
Plug in the wiring harness to the headlight assembly.
Anchor it with the three nuts and the one 10 mm bolts.
Plug in the wiring harness to the parking light and mount it into the vehicle.
Secure it with the push clip by inserting the body of the clip into place and pushing the center down to lock it.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20+ years' experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly, that's going to save you time and money. Thank you and enjoy the video.
In this video I'm going to show you how to replace the headlights both just do the bulbs as well as replace the whole headlight assemblies on this '02 Toyota Tundra. Tools you will need are a 10mm socket with a ratchet and extension, as well as a Phillips and flat blade screwdriver. If you're just looking to replace a bulb I'll come right in behind and there's a connector right here. This connector you want to shake up and down, side-to-side, and then eventually it will pull off. Let's get this connector off, and then this boot here you can pull it up and off and I can see my bulb is already loose in here. Then once you get this back see this piece of wire here my fingers on press that wire up and out and then once this boot comes off your bulb comes up and out. To put it back in, pull the wire out of the way, put your bulb back in, push the wire down, and lock it in place. Take your boot and put it back in place, and then you take your connector and plug the light back in. Maybe you are looking to replace the whole headlight assembly because maybe you got in a little accident or something and broke one of the headlights. Or maybe you're looking to take your truck looking from this to more like something like this. Let's look at that again. Here's our truck before with the old lights, and now after with a new set of lights from 1A Auto.
Really in just about 45 minutes to an hour you can do this with basic tools and you really take miles off the front of your truck. Use a Phillips screwdriver. Kind of work it into this screw bit and turn a little bit, and then use a flat blade screwdriver and pry it up. This center should come up first and then the whole clip should come out. Once you have that out, you want to pull on the light and you can kind of shake it loose. If you pull really firmly, it comes forward. Then around back here is your connector. You can press the button and disconnect the bulb. Now to remove your headlight, there are four fasteners; a 10mm bolt here, a 10mm nut down here, and then two 10mm nuts over here; one there, and one there. I'm going to fast forward as I remove that bolt and the three nuts. Once those bolts are out, lift up on this side of the light, lift up on the inside of the light. The light comes out. Remove your connector.
Your headlight from 1A Auto will go right in and connect to your connector. Put the light in. Put it down on these two studs over here first. Go onto this one and then up there. We'll speed it up again here as I put those nuts and bolts on by hand first and then tighten them up nice and snug. You don't have to have them too tight just enough to hold the light together. When you're putting it back in, this tab here in the fender goes between this tab here so plug your bolt in. Feed it in and kind of look back here and see how it's going in. Make sure it's pressed against the light. Make sure it is up on top there. Clips right in. Take your little top clip push it together down in and you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person.
TY687-B001R
In Stock
Product Reviews
Loading reviews
4.00/ 5.04
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
1
Fine Quality Part
Robert
February 27, 2018
This part is a quality item and was easy to replace thanks to the available on-line tutorials. Swapped it in for the damaged headlight with very little effort. And part was shipped and received lightning fast!
Head light
Victoria
October 7, 2020
Awesome and quick service!
Not good quality
Sean
November 16, 2022
cheaply made, broke before install... where the spring is held down on the frame of the light just busted rite off just like i seen in a video on this same light...
310 K+ and still like new!
Philip
April 11, 2023
I have put more than 310,000 miles on my '03 Tundra. I get an offer to buy it about every two weeks. Thanks to 1A Auto (and Toyota!) I have no desire or need to replace it. The parts from 1A Auto always fit and work like they came with the truck. Keeping you vehicle on the road is what 1A Auto is all about!
Phil in Georgia
Customer Q&A
Does this include the bulb?December 9, 2020
Paul E
10
New light bulbs are not included. Occasionally, manufacturers leave test bulbs in the lights. If you receive test bulbs, you'll want to replace them with your original bulbs or with new bulbs.
December 9, 2020
Emma F
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Toyota is a registered trademark of Toyota Motor Corporation. 1A Auto is not affiliated with or sponsored by Toyota or Toyota Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.