Replaces

Toyota Sequoia Tundra Window Regulator - 1AWRG01970

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Regulator Option:   without Motor
  • Operation:   Power

This window regulator is just what you need to get your vehicle in good working form again!

Specifications:

  • Fits LH (Driver Side) FRONT
  • Power operation
  • Replaces dealer part numbers: 69802-0C010, 69802-0C020, 698020C010, 698020C020
  • Direct replacement
  • Built to strict quality control standards
  • Does NOT include the power window motor
This window regulator is a great replacement that offers good cost savings over the dealer part!

Please Note:

This window regulator is designed to work with factory style motors only.  Due to variations in aftermarket designs, replacement motors may not have the correct gear style.

Please Note:

This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. It has been subjected to extensive testing and quality control standards. That is why we offer this regulator with our superior warranty!

Rigorously Tested

Build to strict quality standards

Highest Quality Materials

Made from the highest quality materials for extreme durability and premium performance.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the Battery (0:41)
    • Disconnect the negative battery cable with a 10mm wrench
  2. step : Removing the Door Panel (0:54)
    • Pry off the mirror base trim piece with a flat blade screwdriver
    • Pry up the window switch panel with a flat blade screwdriver
    • Disconnect the window switch wiring harness
    • Pry off the trim piece beneath the door pull with a flat blade screwdriver
    • Pry off the courtesy light with a flat blade screwdriver
    • Disconnect the courtesy light wiring harness
    • Pry off the trim piece inside the door handle with a flat blade screwdriver
    • Pry off the trim piece at the front top corner of the door panel with a flat blade screwdriver
    • Remove the Phillips head screw at the front top corner of the door panel
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw beneath the door pull
    • Pry off the door handle bezel with a flat blade screwdriver
    • Pry the two plastic pins out of the rear edge of the door panel with a flat blade screwdriver
    • Pry out the door panel with a door panel clip tool or putty knife
    • Lift the door panel up and off
    • If any pins remain in the door panel remove them with pliers
    • Push the pins into the door panel
    • Carefully peel back the water shield
    • Remove the three 10mm bolts from the speaker
    • Disconnect the speaker wiring lead Pull off the speaker
  3. step : Removing the Window Regulator (4:29)
    • Disconnect the window motor lead
    • Unclip the window motor wiring from the door
    • Remove the two 10mm bolts from the window track
    • Remove the four 10mm bolts from the regulator
    • Lower the window by hand
    • Remove the two 10mm bolts that hold the window to the regulator
    • Raise the window by hand
    • Hold the window in place with painter's tape
    • Pull the window regulator out through the door
  4. step : Reinstalling the Regulator (7:10)
    • Insert one of the bolts into the window regulator
    • Push the regulator into the door
    • Hang the regulator by its bolt
    • Insert the four 10mm bolts into the regulator
    • Insert the two 10mm bolts into the window track
    • Remove the painter's tape from the window
    • Connect the window motor lead
    • Connect the negative battery cable with a 10mm wrench
    • Connect the window switch wiring harness
    • Lower the regulator with the switch
    • Lower the window onto the regulator
    • Insert the two 10mm bolts that hold the window to the regulator
    • Test the regulator with the switch
    • Disconnect the window switch wiring harness
  5. step : Reinstalling the Door Panel (9:41)
    • Put the water shield into place
    • Put the speaker into place
    • Connect the speaker wiring lead
    • Insert the three 10mm bolts into the speaker
    • Lift the door panel into place
    • Push in the door panel clips
    • Push on the mirror base trim piece
    • Push on the door handle bezel
    • Connect the window switch wiring harnesses
    • Push in the window switch panel
    • Connect the courtesy light wiring harness
    • Push on the wiring harness
    • Insert the Phillips screw beneath the door pull
    • Insert the Phillips screw into the door handle
    • Insert the Phillips screw at the top front corner of the door panel
    • Push on the trim piece at the top front corner of the door panel
    • Push on the trim piece inside the door handle
    • Push on the trim piece beneath the door pull
    • Push the two plastic clips into the rear of the door panel
  6. step : Reconnecting the Battery (11:59)
    • Connect the negative battery cable with a 10mm wrench, if you have not already done so

Tools needed for replacement:

    General Tools

  • Putty Knife

  • Materials, Fluids, and Supplies

  • Painter's Tape

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Door Panel Removal Tool

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2001-2007Toyota Sequoia Toyota Sequoia Front Power Window Regulator without Motor Driver Side
2004-2006Toyota Tundra Toyota Tundra Double Cab Front Power Window Regulator without Motor Driver Side
Part #: 1AWRG01970


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(12:24 min)