Toyota Sequoia Tundra Lighting Kit 4 Piece Set - 1ALHT00102

Frequently bought together

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Quantity:   4 Piece Set
  • Kit Includes:
      (2) Parking Lights
      (2) Headlights


  • Comes as a SET of 4
    • Fits both LH (Driver Side) & RH (Passenger Side)
  • Replaces dealer part numbers: 81110-0C030, 81150-0C030, 81520-0C030, 815200C030, 811100C030, 811500C030, 81510-0C030, 815100C030
  • DOT (Department of Transportation) & SAE (Society of Automotive Engineers) approved
  • Includes lenses & housings
  • Bulbs not included
These lights are great replacements and have good cost savings over lights from the dealer.

Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

Bulb Note:

These lights do not include bulbs.  If you happen to receive a product with bulbs, the bulbs are for testing and not covered under our warranty.  Our warranty applies to the light assembly only.

  1. step : Changing the Headlight Bulbs (0:55)
    • Reach down behind the headlight and pull the connector from the headlight.
    • Remove the rubber boot.
    • Push the retainer in and up.
    • Pull the bulb free.
    • Put the new one in place and put the retainer in and down.
    • Replace the rubber boot.
    • Reconnect the harness.
  2. step : Removing the Headlight Assembly (2:28)
    • Remove the Phillips clip above the side light.
    • Pull the side light forward and out.
    • Disconnect the connectors on the back of the side light.
    • Remove the four 10mm bolts securing the headlight.
    • Disconnect the connecter and pull the headlight up and out.
  3. step : Replacing the Headlight Assembly (4:48)
    • Line up the new headlight and slide it into place.
    • Replace the four 10mm bolts.
    • Reconnect the harness.
    • If you need to adjust the headlight angle do it before replacing the side light.
    • Reconnect the side light.
    • Line it up and push it in to place.
    • Replace the Phillips clip above the side light.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

4.29/ 5.0
7 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
The new headlights made my 06 Tundra with 324000 miles see again. Easy install-fit great . Would reccommend. 1Aauto great service, will use again.
March 3, 2017
Great replacement lights
These were easy to install and made a tremendous difference in the appearance not to mention improved vision at night! Cant believe I waited so long to replace the fpggy ones!
August 23, 2017
Head light and turn signal replacement parts
The parts were delivered fast, I watched the video which was helpful, the biggest problem I have is that the turn signal and head light do not line up correctly, so they are not flush with each other. I found the turn signal has way to much molded plastic to allow them to sit flush, I spent a long time with a dremel tool to remove excess plastic just so I could get the pin back in the hold the turn signal in place. I also had a problem with the lamp socket, the electrical pins are cheaply made, so I just used the old lamp sockets.
August 18, 2018
Absolutely great upgrade!
This was so easy and makes a huge difference in the way my 2007 Sequoia looks. The bulbs that come pre-installed are really bright. Night lighting is like new again. Install is very simple. Watch video. Took just (20 minutes for side one, (10j minutes side two. Would highly recommend for the price. Get the lamps and signals that this complete kit has. (Instead of just doing the headlamps).
September 6, 2018
Great light kit
Easy install, actual install work took about 30 minutes total. Replaced original 2006 Toyota Sequoia headlights. Hardest part of the install was talking to the neighbors asking what I was doing. New lights fit and look like new
February 11, 2019
tundra lights
great deal
May 10, 2019
Cured problem of old, faded headlights
Cured the problem of old, faded headlights. Tried lens cleaner and polisher, to no avail, Replacement units ordered fit precisely. Change out was made easy by available instruction video. I am not a mechanic, but did it myself in less than 2 hours.
November 8, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Do they adjust. The one I have now are two high and won’t adjust down anymore?
Billy S April 14, 2019
Not sure, all I had to do was install. They worked perfect. Sorry I cant help you.
D N April 14, 2019
yes, they do have 2 screw driver settings, 1 for left and right, the other one for up and down. you just have to remove a white plastic cap, then you will see the screw driver setting. but yes, they do adjust.
L S April 15, 2019
Yes, these lights do have adjusters in the back to adjust.
Christa R April 15, 2019
Year Make Model Description
2005-2007Toyota Sequoia Toyota Sequoia Lighting Kit 4 Piece Set
2005-2006Toyota Tundra Toyota Tundra Double Cab Lighting Kit 4 Piece Set
Part 1ALHT00102
In Stock

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.