Replaces

Toyota Sequoia Tundra Interior Door Handle - 1ADHI00519

This door handle is just what you need to get your vehicle in good looking form again!

Specifications:

  • Fits LH (Driver Side) FRONT or REAR
  • Smooth Fawn Finish
  • Direct replacement
  • Built to strict quality control standards

This door handle is a great replacement and has good cost savings over the dealer unit.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Disconnecting the Battery (0:41)
    • Disconnect the negative battery cable with an 8mm wrench
  2. step : Removing the Door Panel (0:52)
    • Pry off the mirror base trim panel with a flat blade screwdriver
    • Pry off the window switch panel with a flat blade screwdriver
    • Disconnect the window switch wiring harness
    • Pry off the screw cover panel below the door pull with a flat blade screwdriver
    • Pry off the courtesy light with a flat blade screwdriver
    • Disconnect the courtesy light wiring harness
    • Pry off the door handle trim piece with a flat blade screwdriver
    • Pry off the screw cover panel at the top front corner of the door with a flat blade screwdriver
    • Remove the Phillips head screw at the top front corner of the door
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw below the door pull
    • Pry off the door handle bezel with a flat blade screwdriver
    • Push in the clips at the back of the door panel
    • Pull the clips out of the back door panel
    • Pry the door panel off of its clips with a putty knife or door panel clip tool
    • Remove any clips that remain in the door with needle nose pliers
    • Push those clips into the door panel
  3. step : Removing the Door Handle (4:06)
    • Slide the door handle back and pull it off
    • Pull the cables out of the door handle
  4. step : Installing the New Door Handle (4:24)
    • Turn the new door handle upside down
    • Put the top cable into the lower clip (still holding the handle upside down)
    • Put the bottom cable into the lower clip (still holding the handle upside down)
    • Turn the handle right side up
    • Push the door handle into place
  5. step : Reinstalling the Door Panel (5:07)
    • Put the door panel into place, pulling the wiring harnesses through their cavities
    • Push the door panel clips in
    • Push on the mirror base trim panel
    • Push the door handle bezel in
    • Connect the window switch wiring harness
    • Push in the window switch panel
    • Connect the courtesy light wiring harness
    • Push in the courtesy light
    • Insert the Phillips screw below the door pull
    • Insert the Phillips screw into the door handle
    • Insert the Phillips screw at the top front corner of the door panel
    • Push in the screw cover below the door pull
    • Push in the screw cover into the door handle
    • Push in the screw cover at the top front corner of the door panel
    • Push the clips into the back of the door panel
  6. step : Reconnecting the Battery (6:55)
    • Reconnect the negative battery cable

Tools needed for replacement:

    General Tools

  • Putty Knife

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Specialty Tools

  • Door Panel Removal Tool

  • Wrenches - Metric

  • 8mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Perfect fit and after watching the video, it only took about 2 minutes to install. Thanks for the help!
January 16, 2018
Purchased
5 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2007 Toyota Sequoia Front or Rear Fawn Interior Door Handle Driver Side
  • 2004-2006 Toyota Tundra Double Cab Front or Rear Fawn Interior Door Handle Driver Side

This part replaces:

  • OE # 692060C030E1
  • Dorman 81262
Part #: 1ADHI00519

How-to Video:

(07:19 min)