Our aftermarket cooling fan blades are some of the highest quality replacements on the market!

Specifications

  • Direct fit
  • Number of blades: 7
  • Mounting: bolts to the fan clutch
  • 100% Performance factory tested
  • Built to strict quality control standards
  • Correct for Toyota trucks / SUV's with the following engine as listed per application:
    • V6 3.4L (5VZFE)

Now you can buy a high quality replacement Toyota cooling fan blade that has substantial cost savings over a dealer unit.

Our electrical and electronic parts are subject to strict quality control testing .  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Skid Plate and Draining the Coolant (1:01)
    • Disconnect your negative battery cable with a 10mm wrench
    • Remove the 10mm bolts from the skid plate
    • Place a drain pan underneath the radiator
    • Pull the drain plug and drain the fluid
  2. step : Removing the Intake (1:58)
    • Remove the two 10mm nuts from the name plate
    • Remove the 10mm bolt from the hose clamp
    • Loosen the two hose clamps from the air intake tube with a Phillips screwdriver
    • Disconnect the air sensor
    • Move the air intake to the side
  3. step : Removing the Radiator Fan (2:31)
    • Slide the clamp from the radiator hose
    • Remove the hose from the radiator
    • Disconnect the overflow tube
    • Remove the bottom two bolts from the fan shroud
    • Loosen the top bolts from the fan shroud
    • Hold the radiator fan with a 12mm wrench
    • Remove the other three bolts with a 12mm wrench
    • Thread one of the bolts on backwords
    • Jar a flat blade screwdriver to hold the assembly to remove the last bolt
    • Remove the last two bolts from the fan shroud
    • Manuever the radiator fan and shroud up and out
  4. step : Installing the Radiator Fan (5:03)
    • Insert the fan and shroud into place at the same time
    • Insert the four bolts to the shroud
    • Insert the four nuts to the radiator fan
    • Torque the bolts between 15-16 foot-pounds
    • Insert the radiator hose into place
    • Slide the radiator hose clamps into place
    • Reconnect the overflow tube
  5. step : Installing the Intake (6:22)
    • Insert the air intake hose into place
    • Tighten the two hose clamps with a Phillips screwdriver
    • Insert the 10mm bolt to the hose clamp
    • Insert the two 10mm nuts to the name plate
    • Connect the air wiring sensor
  6. step : Reinstalling the Skid Plate (6:59)
    • Tighten the radiator drain plug
    • Insert the skid plate into place
    • Tighten the bolts to the skid plate
  7. step : Refilling the Coolant (7:12)
    • Refill the radiator directly with the recommended amount
    • Reconnect the negative battery cable
    • Turn the car on and make sure it reaches the operating temperature
    • Let the engine cool down
    • Check the coolant level
    • Fill any necessary fluid to the recommended amount

Tools needed for replacement:

    General Tools

  • Drain Pan

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 12mm Socket

  • Wrenches - Metric

  • 10mm Wrench
  • 12mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(08:35 min)

Tools List:

    General Tools

  • Drain Pan

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 12mm Socket

  • Wrenches - Metric

  • 10mm Wrench
  • 12mm Wrench



This part replaces:

  • OE # 1636162010
  • Hollander 325-50549
  • Dorman 620-534

Vehicle Fit

  • 1996-2002 Toyota 4Runner Radiator Cooling Fan Blade V6 3.4L
  • 1995-1998 Toyota T100 Radiator Cooling Fan Blade V6 3.4L
  • 1995-2004 Toyota Tacoma Radiator Cooling Fan Blade V6 3.4L
  • 2000-2004 Toyota Tundra Radiator Cooling Fan Blade V6 3.4L
Part #: 1ARFB00001

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More