Replaces

Toyota Lexus Front Lower Ball Joint Pair - 1ASFK00426

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   Pair

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT LOWER
  • Replaces dealer part numbers: 4333039435, 43330-39435, 4333039285. 43330-39285, 4333009050, 43330-09050, 4333039285, 43330-39285
  • Direct replacements
  • Built to strict quality control standards

 

Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greasable versions.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:58)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Pull off the hub cap
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Control Arm (3:49)
    • Straighten out the ball joint cotter pin, using a pair of needle noise pliers
    • If the cotter pin is stuck, cut the head with wire cutters
    • Then tap the stuck cotter pin out with a hammer and punch
    • Apply penetrating oil to the cotter pin if necessary
    • Pull the cotter pin out with needle nose pliers
    • Loosen the 19mm ball joint nut
    • Loosen the ball joint from the wheel spindle with a pickle fork and hammer
    • Remove the 19mm nut
    • Remove the two 17mm nuts connecting the ball joint to the control arm
    • Remove the 17mm bolt connecting the ball joint to the control arm
    • Separate the ball joint from the control arm with a pry bar
  3. step : Installing the Ball Joint (9:12)
    • Thread the grease fitting onto the new ball joint by hand
    • Tighten the grease fitting with a 10mm wrench
    • Put the ball joint into the wheel spindle
    • Thread the 19mm castle nut onto the ball joint stud
    • Lower the control arm with a pry bar
    • Put the ball joint bracket studs into the control arm
    • Fasten the 17mm nuts onto the ball joint bracket
    • Insert the 17mm bolt into the ball joint bracket
    • Tighten the two 17mm nuts to 94 foot-pounds of torque
    • Tighten the 17mm bots to 94 foot-pounds
    • Tighetn the 19mm nut onto the ball joint stud
    • Make sure the castle nut lines up with the cotter pin hole
    • Insert the cotter pin sideways, with the longer leg facing in toward the center of the vehicle
    • Bend one of the cotter pin legs around the nut with pliers
  4. step : Reattaching the Wheel (11:53)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 21mm Socket
  • 19mm Socket
  • 17mm Socket

  • Specialty Tools

  • Pickle Fork

  • Wrenches - Metric

  • 17mm Wrench
  • 19mm Wrench
  • 10mm Wrench

5.00/ 5.0
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
4
0
0
0
0
Great replacement
No issues so far, rides much better after 250k miles wore out the originals
April 28, 2018
99 Avalon hub & bearing parts
Purchased new hub & bearing assembly for my 99 Avalon & all the parts fit exactly as they should & were replaced fairly quickly. I am not a mechanic so the video helped me a great deal on how to go about replacing the parts properly. I highly recommend 1aauto parts & videos. Thank you for your help!
April 26, 2019
Ball joints
Perfect fit AWESOME priceWrite
June 12, 2019
good parts
All of my parts were there and the worked and fit how they were suppose to .Everything came when it said it would
June 20, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Do these have zerk fittings so I can re-grease them?
D O July 29, 2019
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greasable versions.
Jessica D July 30, 2019
Year Make Model Description
1992-2001Lexus ES300 Lexus ES300 Front Lower Ball Joint Pair
1999-2003Lexus RX300 Lexus RX300 Front Lower Ball Joint Pair
1995-2004Toyota Avalon Toyota Avalon Front Lower Ball Joint Pair
1992-2001Toyota Camry Toyota Camry Front Lower Ball Joint Pair
1998-2003Toyota Sienna Toyota Sienna Front Lower Ball Joint Pair
1999-2003Toyota Solara Toyota Solara Front Lower Ball Joint Pair
Part 1ASFK00426
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.