This combination headlight/turn signal switch is a new, aftermarket replacement part. It is designed to REPLACE original units that are prone to failure. It's just what you need to get your vehicle in good working order again!

Specifications:

  • Brand New Turn Signal/Headlight Multifunction Switch
  • Multi-Function Switch Controls:
    • Headlight
    • High Beam
    • Turn Signal
  • Number of Terminals: 16
  • Replaces dealer part numbers: 84140-06010, 84140-26140, 8414006010, 8414026140
  • Direct replacement
  • Built to strict quality control standards
  • Fits models WITHOUT Automatic Headlights
  • Fits models WITHOUT Fog Lamps

This headlight/turn signal switch is designed to replace your original with no modifications necessary. It is a great replacement and offers good cost savings over the dealer unit.

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Disconnecting the Battery (0:40)
    • Loosen the negative terminal with a 10mm wrench
    • Let the disconnected battery sit for 30 minutes to drain power from the modules
  2. step : Removing the Dimmer Switch (0:57)
    • Remove the Phillips head screw from the lower steering wheel column
    • Turn your key to accessory mode
    • Turn the wheel 90 degrees
    • Remove the Phillips head screw from the column
    • Turn the wheel 180 degrees
    • Remove the Phillips head screw from the column
    • Separate the steering column cover with a flat blade screwdriver
    • Remove the upper portion
    • Remove the panel from the tilt column lever
    • Remove the bottom portion
    • Disconnect the switch connector
    • Remove the two Phillips head screws from the switch
    • Remove the switch
  3. step : Installing the Dimmer Switch (3:27)
    • Insert the switch into place
    • Tighten the two Phillips head screws to the switch
    • Connect the switch connector
    • Insert the upper steering column cover into place
    • Tilt the column up and insert the lower column portion
    • Press the tilt trim piece into place
    • Tighten the Phillips head screw to the bottom of the column
    • Turn the key to run
    • Rotate the wheel and tighten the two Phillips screws
    • Straighten the wheel
    • Remove the key
  4. step : Connecting the Battery (5:16)
    • Reconnect the battery with a 10mm wrench
    • Turn the key to the on position
    • Check the parking, low beam, high beam, and turn signals for operation

Tools needed for replacement:

    Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Wrenches - Metric

  • 10mm Wrench

4.8 / 5.0
6 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
5
1
0
0
0
Recent purchase and install of TS/HS Lever
When I needed a new lever I thought of 1aauto. The price was right and I reviewed the installation video for what appeared to be a challenging task. However, after viewing the video, and getting the lever I completed the removal of the broken lever and installed the new one in less than 30 minutes. It was easy and pretty much the same as in the 1aauto video. The lever works as described.
December 23, 2017
Purchased
4 months ago
Turn signal control install
Worked as suggested. Thank you for your help. I will look to you first for future needs. Tom.
March 1, 2017
Purchased
1 year ago
installed part
part fit good and worked just fine thank you. Your review must be at least fifty characters in length in length inlength inlength in length in length in length.
August 29, 2017
Purchased
8 months ago
Can't say much
Part came quicker than i expected and was a perfect fit. The install video made it a breeze and took less than 20 min to do the job.
November 8, 2017
Purchased
5 months ago
Installed in 1998 Camry. Works perfect. Exact fit.
Installed in 1998 Camry. Works perfect. Exact fit.
January 12, 2018
Purchased
3 months ago
Easy install
Switch was easy to install and restored all fan speeds. Delivered on time.
March 2, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1996-1999 Toyota 4Runner Combination Switch without Fog Lights
  • 1998-1999 Toyota Avalon Combination Switch without Fog Lights
  • 1997-2001 Toyota Camry Combination Switch without Fog Lights
  • 1995-2000 Toyota Celica Combination Switch without Fog Lights
  • 2001-2003 Toyota Prius Combination Switch without Fog Lights
  • 1996-2000 Toyota Rav4 Combination Switch without Fog Lights
  • 1998 Toyota Sienna Combination Switch without Fog Lights without Automatic Headlights

This part replaces:

  • OE # 8414006010
  • OE # 8414026140
  • Standard Motor Products CBS-1009
Part #: 1AZTS00212

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(05:56 min)