Replaces

Toyota Camry Solara CV Axle Shaft TRQ CSA82160 - 1AACV00093

Specifications:

  • Fits RH (Passenger Side) FRONT
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:48)
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack near the pinch weld
    • Secure the vehicle on jack stands at the unibody frame rail, and place it just ahead of the lower control arm on the rear
    • Repeat the process for the other side so the vehicle is level
    • Remove the hub cap
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Axle Nut (2:23)
    • Bend the cotter pin straight out with needle nose pliers
    • Pull the cotter pin up and out
    • Remove the lock cover on the nut
    • Hold the hub still with a pry bar
    • Break the axle nut socket loose with a 30mm socket and breaker bar
    • Leave the nut at the end of the axle
    • Hammer the axle out
    • Remove the axle nut
  3. step : Removing the CV Axle from the Spindle (3:26)
    • Remove the ABS retainer from the spindle
    • Break the 22mm strut nuts loose and remove them
    • Tap the bolts out of the spindle with a punch and hammer
    • Pull the spindle down and out of the strut
    • Pull the axle out of the spindle
  4. step : Removing the CV Axle from the Differential (4:25)
    • Have a drain pan ready
    • Remove the 14mm bolt from the bearing on the end of the axle shaft
    • Push together to two tabs from the snap ring
    • Insert two pry bars to 3 and 9 o'clock on the axle, applying even pressure
    • Carefully work the snap ring out of its holder inside the differential
    • Remove the axle from the differential
  5. step : Installing the CV Axle to the Differential (6:40)
    • Align the axle splines with the splines in the differential
    • Work the axle into the differential
    • Insert the snap ring around the CV axle, aligning the ears up
    • Tighten the 14mm bearing bolt
    • Torque the bolt to 24 foot-pounds
  6. step : Inserting the CV Axle to the Spindle (7:31)
    • Line up the splines into the hub
    • Start the axle nut on the end of the axle
    • Reinstall the 22mm strut bolts to the spindle
    • Tighten the nuts to 156 foot-pounds
    • Connect the ABS retainer
  7. step : Installing the Axle Nut (8:28)
    • Tighten down the axle nut with a 32mm socket and ratchet
  8. step : Reinstalling the Wheel (8:34)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to partial weight on the ground
    • Tighten the lug nuts to 76 foot-pounds in a crossing or star pattern
    • Lower the jack
    • Torque the axle to 217 foot-pounds
    • Reinstall the lock cap and new cotter pint to the axle nut
    • Reinstall your hubcap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Drain Pan
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 32mm Socket
  • 21mm Socket
  • 22mm Socket
  • 12mm Socket

4.5 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
1
0
0
0
1999 Toyota Camry CE Passenger Side CV Shaft Replacement
Ordered a replacement 1999 Toyota Camry CE passenger side CV shaft. The one I took off did not have a anti lock brake spline on it. The one I received from 1A Auto did have the anti lock brake spline. Called 1A Auto and they indicated it would fit ok. Very helpful on the phone. Installed it with no issues. Thanks.
January 16, 2018
Purchased
8 months ago
Great product. Slight shipping damage.
I was very please with the price and quality of this product. It was exactly as advertised and saved me hundreds of dollars over purchasing an OEM axle. My only complaint was that the packaging didn't quite hold up to the wear and tear of shipping. The box came smashed in and the dust covers were slightly bent. Nothing structural was damaged and I was able to bend the dust covers back into place.

Overall I'm extremely satisfied with the product itself. But it could probably benefit from being packaged a little bit better.
October 28, 2017
Purchased
11 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1992-2001Toyota Camry Toyota Camry L4 2.2L CV Axle Shaft Passenger Side TRQ CSA82160
1999-2001Toyota Solara Toyota Solara L4 2.2L CV Axle Shaft Passenger Side TRQ CSA82160

This part replaces:

  • Hollander 447-59081R
  • TRQ CSA82160
  • A1 Cardone 66-5044
  • OE # 4341006161
Part #: 1AACV00093


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: CSA82160

How-to Video:

(10:02 min)