Replaces

Toyota Camry Exhaust System - 1AEMK00207

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Kit Includes:
      (1) Rear Muffler
      (1) Intermediate Pipe
      (1) Front Pipe with Catalytic Converter
      Exhaust Gaskets

Front Pipe Specifications:

  • Replaces Front Exhaust Pipe with REAR converter
  • Replaces dealer part numbers: 17410-03140, 1741003140
  • Details:
    • Inlet:
      • 3 Bolt triangular flange
    • Outlet:
      • 2 Bolt oval flange
    • NO Oxygen sensor provisions
  • High quality 409 grade stainless steel
  • Includes all Pipes and flanges for direct installation (additional clamps may be required)
  • Certified for the following agencies:
    • US Environmental Protection Agency (EPA)
    • Ministry of Environment, Ontario & British Columbia - Canada
  • Built to strict quality control standards
  • Correct for vehicles with or without California Emissions

Intermediate Pipe Specifications:

  • Direct Fit Intermediate Exhaust Pipe with Gaskets
  • Fits between the front pipe & rear muffler section
  • Front connection type: 2 bolt flange
  • Rear connection type: 2 bolt flange
  • Replaces dealer part numbers: 17420-03080, 1742003080
  • Built to strict quality control standards

Rear Muffler Specifications:

  • Direct Fit Rear Muffler Section with Gasket
  • 2 bolt flange connection
  • Direct bolt on replacement
  • No modification necessary
  • Replaces dealer part numbers: 17430-03191, 1743003191, 17430-03190, 1743003190, 17430-03192, 1743003192, 1418460G00, 9091706008, 9091706012, 1743003192, 141846 0G00, 90917 06008, 90917 06012
  • Built to strict quality control standards

Item Condition: New

5 Year Warranty

This item is backed by our 5-year warranty. In the event this item should fail during intended use, we will replace the part free of charge.

Emissions Note:

Due to state emissions regulations:

We cannot ship this item to California, as it is not California Air Research Board approved.

In the state of New York, this item cannot be installed on California emissions equipped vehicles.

In the state of Maine, this item cannot be sold for or installed on a 2001 model year or newer, California emissions equipped vehicle.

Emissions information can be found on a tag under the hood or from a dealership based on your VIN.

  1. step : Removing the Front Pipe with the Flex Pipe and Cat Converter (1:12)
    • Jack up and support the vehicle on jack stands
    • Remove the three 14mm nuts on the front pipe flange on the bottom of the exhaust manifold
    • Loosen the O2 sensor with a 22mm wrench
    • Mark the side of the O2 sensor
    • Count the number of rotations it takes to remove the sensor
    • Unbolt the two 12mm bolts securing the exhaust before the flex pipe
    • Remove the two 12mm bolts securing the exhaust hanger to the subframe
    • Lower and remove the exhaust
  2. step : Removing the Mid Pipe (4:50)
    • Pull the stud out of the rubber hanger
    • Support the remaining pipe with a bungee chord
    • Remove the 14mm hardware from the end near the cat convertor
    • Remove the two 14mm nuts from the end near the muffler
  3. step : Removing the Muffler (5:43)
    • Jack up and support the vehicle on jack stands
    • Remove the two 14mm nuts on the flange
    • Spray the exhaust hangers with rust penetrant
    • Pry off the hangers from the studs
    • Remove the muffler
  4. step : Installing the Muffler (7:47)
    • Reinstall the muffler into its hangers
    • Clean the flange surfaces
    • Insert a gasket onto the flange
    • Tighten the two 14mm nuts to the flange
  5. step : Installing the Mid-Pipe (8:11)
    • Install the mid-pipe into the hanger
    • Clean the surface before installing the new gasket
    • Tighten the two 14mm bolts to the end near the muffler
    • Tighten the hardware as tight as possible evenly to seal the gasket
    • Counter-turn the O2 sensor by the previous counted amount
    • Thread the O2 sensor into the mid-pipe
    • Tighten the O2 sensor with a 22mm wrench
    • Attach a gasket onto the end pipe
    • Insert the 14mm hardware into place and tighten the cat convertor to the pipe
  6. step : Installing the Front Pipe with the Flex Pipe and Cat Converter (12:09)
    • Insert the hanger over the arm
    • Line the front studs of the exhaust manifold into place with a new gasket
    • Reinstall the two 12mm bolts on the hanger
    • Tighten the 12mm bolts with a socket and ratchet
    • Clean the surface before installing the new gasket
    • Insert the 14mm hardware into place and tighten the convertor to the pipe
    • Tighten the hardware as tight as possible evenly to seal the gasket
    • Attach a gasket onto the end pipe
    • Tighten the two 12mm bolts to the brace around the exhaust pipe
    • Tighten the 14mm nuts to the front pipe flange

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 12mm Socket

  • Wrenches - Metric

  • 12mm Wrench
  • 14mm Wrench

4.33/ 5.0
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
2
0
0
0
Exhaust System for Camry
I was amazed on how perfect of a match this exhaust system was. Everything matched up great from the flanges to the bolt pattern, hangers and pipe bends. If you order, make sure you call first to verify you have everything you need. Customer service recommended I purchase an O2 sensor as well. I was glad I took their advice because the old sensor would not budge. For the price, exhaust match and quality, I would highly recommend 1aAuto.
March 13, 2017
everything fit perfectly
All gaskets are parts fit perfectly and look like heavy gauge steel, but there were no nuts or bolts. I used 300 series stainless nuts and bolts so that each pipe could be replaced separately in the future.
July 15, 2019
Good product, missing hardware
Product arrived fast and fit nicely on the car, the only downside to the complete exhaust system was that there were no mounting hardware for the cat pipe to the resonator pipe and likewise for the resonator pipe to the muffler. Im not sure if it was a fluke, but just be prepared to have to possibly visit an auto parts store or a hardware store for the nuts and bolts to bolt everything together. Other than that, product fit as it should and the car runs alot quieter now.
November 5, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does this have the threaded hole for the oxygen sensor?
Bill S September 2, 2018
The front pipe states that it does not have the O2 sensor provision. That would need to done by a shop of some kind.
Corey M September 3, 2018
Is this exhaust system federal EPA??
Jaime R September 18, 2018
I dont know, but I have passed Massachusetts auto inspection every year since I change it (complete set).
Y A September 18, 2018
Yes this will work for both Federal and California emissions. Please note there there are no O2 sensor provisions on these pieces.
Tim K September 19, 2018
Year Make Model Description
1997Toyota Camry Toyota Camry L4 2.2L California Emissions Exhaust System
1998-1999Toyota Camry Toyota Camry L4 2.2L Exhaust System
Only 6 left in stock
Part 1AEMK00207
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.