This inner tie rod end is just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits either the LH (Driver Side) or RH (Passenger Side) FRONT INNER
  • Replaces dealer part number: 53010-SR3-010, 53010SR3010
  • Direct replacement
  • Built to strict quality control standards

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:40)
    • Loosen the lug nut covers
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Tie Rod (1:00)
    • Measure from the boot to the outer tie rod and record it
    • Loosen the 19mm nut on the tie rod with a 19mm wrench
    • Remove the cotter pin with pliers
    • Remove the castle nut with a 17mm socket
    • Hit the knuckle with a hammer
    • Twist the tie rod out
  3. step : Installing the New Tie Rod (2:13)
    • Twist on the new tie rod
    • Push the outer tie rod down into the knuckle
    • Replace the castle nut
    • Push the cotter pin into place and bend the ends in separate directions with pliers
    • Measure and double check the distance of the boot to the tie rod
    • Turn the tie rod joint with the 14mm wrench to adjust the distance
    • Replace and tighten the 19mm nut
  4. step : Reattaching the Wheel (3:15)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 17mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 19mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1994-1997Acura Integra Acura Integra Front Inner Tie Rod Driver or Passenger Side
1992-1995Honda Civic Honda Civic Front Inner Tie Rod Driver or Passenger Side
1993-1997Honda Civic Del Sol Honda Civic Del Sol Front Inner Tie Rod Driver or Passenger Side

This part replaces:

  • Moog EV299
  • OE # 53010SR3010
  • OE # 53010-SR3-010
Part #: 1ASTE00122


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(03:54 min)