Specifications:

  • Fits either the LH (Driver Side) or RH (Passenger Side) Front
  • Includes both inner & outer tie rods for 1 side
  • Direct replacement
  • Built to strict quality control standards
  • Correct for both FWD & AWD models

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:46)
    • Remove the center cap with a cap removal tool or pick
    • Loosen the 17mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:42)
    • Loosen the 22mm nut 1/4 a turn while holding the 18mm nut behind it
    • Remove the 13mm nut on top of the tie rod end
    • Remove the 16mm nut on the side of the tie rod end
    • Hand tighten the 16mm bolt and drive the bolt out
    • Pry the tie rod out of the knuckle
    • Hold the 18mm nut from the outer tie rod end
    • Twist off the outer tie rod by hand
  3. step : Installing the Outer Tie Rod (4:00)
    • Set the lock nut to the same position as the original
    • Thread the outer tie rod in while holding the 18mm nut
    • Twist the tie rod with a pair of pliers to insert it into place
    • Hammer the tie rod into the steering knuckle
    • Tighten the 13mm bolt to the grease fitting
    • Tighten the 16mm bolt to the grease fitting
    • Hold the 18mm nut and tighten the 22mm locking nut
  4. step : Reattaching the Wheel (6:33)
    • Slide the wheel into place
    • Start the 17mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 90 foot-pounds in a star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Pick
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Sockets - Metric

  • 16mm Socket
  • 17mm Socket
  • 13mm Socket

  • Specialty Tools

  • Audi Wheel Cap Removal Tool

  • Wrenches - Metric

  • 22mm Wrench
  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1996-2004 Audi A4 Front Inner & Outer Tie Rod Driver or Passenger Side
  • 1996-2004 Audi A4 Quattro Front Inner & Outer Tie Rod Driver or Passenger Side
  • 1998-2004 Audi A6 Front Inner & Outer Tie Rod Driver or Passenger Side
  • 1998-2004 Audi A6 Quattro Front Inner & Outer Tie Rod Driver or Passenger Side
  • 1997-2003 Audi A8 Front Inner & Outer Tie Rod Driver or Passenger Side
  • 1997-2003 Audi A8 Quattro Front Inner & Outer Tie Rod Driver or Passenger Side
  • 2001-2002 Audi Allroad Front Inner & Outer Tie Rod Driver or Passenger Side
  • 2003-2004 Audi RS6 Front Inner & Outer Tie Rod Driver or Passenger Side
  • 2002-2003 Audi S6 Front Inner & Outer Tie Rod Driver or Passenger Side
  • 2001-2003 Audi S8 Front Inner & Outer Tie Rod Driver or Passenger Side
  • 1998-2005 VW Passat Front Inner & Outer Tie Rod Driver or Passenger Side

This part replaces:

  • OE # 4B0419811E, 4F0419811D
  • OE # 4B0419801M
  • OE # 4D0422821A
  • Moog EV440
  • Moog ES3646
Part #: 1ASFK05104

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(07:49 min)