Part Details

  • Quantity: 4 Piece Set

These replacement tie rods are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a SET
    • Includes LH (Driver Side) & RH (Passenger Side) INNER & OUTER
  • Replaces dealer part numbers: 15254061
  • Direct replacements
  • Built to strict quality control standards
  • Does not fit hybrid models

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:03)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:24)
    • Turn the brake rotor by hand or turn the steering wheel to turn the rotor
    • Measure the distance from the end of the boot to the center of the tie rod end
    • Note that measurement
    • Loosen the tie rod lock nut with a 15/16" wrench
    • Loosen the 21mm nut from the tie rod
    • Strike the steering knuckle with a hammer to loosen it
    • Lift the tie rod end out of the steering knuckle
    • Twist off the outer tie rod by hand
  3. step : Installing the Outer Tie Rod (2:18)
    • Twist on the outer tie rod
    • Push the tie rod into the steering knuckle
    • Thread the 22mm castle nut onto the tie rod by hand
    • Measure the distance from the end of the boot to the center of the tie rod end
    • This should be the same as the measurement from Step 2
    • Twist the grease fitting into the tie rod
    • Tighten the castle nut to 50-55 foot-pounds of torque
    • Put the cotter pin into the castle nut
    • Twist on the cotter pin with pliers
    • Hold the inner tie rod with a 16mm wrench
    • Tighten the locking nut with a 15/16" wrench
    • Add grease to the tie rod with a grease gun
  4. step : Reattaching the Wheel (4:24)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100-110 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack
  • Hammer

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 21mm Socket
  • 22mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 16mm Wrench

  • Wrenches - SAE

  • 15/16 Inch Wrench

4.5 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
1
0
0
0
Good quality except grease fittings were a bit weak stripped immediately
I mean don't get me wrong the quality was good, but the grease fitting was very weak and stripped after just a little pressure
June 13, 2018
Purchased
4 months ago
Love this site
I will never order from another site except this one for parts again. This site has gotten me all of my parts within 2 days of ordering them and everything fit great! The videos on this site are very helpful to reference if you get stuck on something too!
April 4, 2018
Purchased
6 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 1 answer
Does the set have grease fittings ?
Chris L on Mar 29, 2017
BEST ANSWER: These outer tie rods will be sealed from the factory.
Anyone know the wrench size for the inner tie rod?
Mikehall05 on Mar 3, 2018

Vehicle Fit

Year Make Model Description
2007-2014Cadillac Escalade Cadillac Escalade Front Inner & Outer Tie Rod 4 Piece Set
2007-2014Cadillac Escalade ESV Cadillac Escalade ESV Front Inner & Outer Tie Rod 4 Piece Set
2007-2013Cadillac Escalade EXT Cadillac Escalade EXT Front Inner & Outer Tie Rod 4 Piece Set
2007-2013Chevy Avalanche 1500 Chevy Avalanche 1500 Front Inner & Outer Tie Rod 4 Piece Set
2007Chevy Silverado 1500 Chevy Silverado 1500 New Body Style Front Inner & Outer Tie Rod 4 Piece Set
2008-2013Chevy Silverado 1500 Chevy Silverado 1500 Front Inner & Outer Tie Rod 4 Piece Set
2007-2013Chevy Suburban 1500 Chevy Suburban 1500 Front Inner & Outer Tie Rod 4 Piece Set
2007-2014Chevy Tahoe Chevy Tahoe Front Inner & Outer Tie Rod 4 Piece Set
2007GMC Sierra 1500 GMC Sierra 1500 New Body Style Front Inner & Outer Tie Rod 4 Piece Set
2008-2013GMC Sierra 1500 GMC Sierra 1500 Front Inner & Outer Tie Rod 4 Piece Set
2007-2013GMC Yukon GMC Yukon Front Inner & Outer Tie Rod 4 Piece Set
2007-2013GMC Yukon XL 1500 GMC Yukon XL 1500 Front Inner & Outer Tie Rod 4 Piece Set

This part replaces:

  • Moog ES800223
  • Moog EV800084
  • OE # 15254061
  • OE # 15254060
Part #: 1ASFK01666


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(05:10 min)