These Outer Tie Rod Ends are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side)
  • Replaces dealer part numbers: 94843587, 94847293, 94854303, 94856276, 4504619175, 4504629305
  • Direct replacements
  • Built to strict quality control standards

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:24)
    • Pry off the hub cap with a pry bar
    • Loosen the lug nuts with a 21mm socket and breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull the wheel off the hub
  2. step : Removing the Ball Joint (1:12)
    • Apply rust penetrant to the ball joint nuts and bolt
    • Loosen the two ball joint nuts with a 17mm socket and breaker bar
    • Loosen the ball joint bolt with a 17mm socket and breaker bar
    • Remove the cotter pin from the ball joint castle nut with needle nose pliers and side cutters
    • Drive the cotter pin out of the castle nut with a hammer and punch
    • Loosen the castle nut with a 19mm wrench and a dead blow hammer
    • Strike the wheel knuckle with a small sledge hammer
    • Remove the two 17mm nuts from the ball joint
    • Remove the 17mm bolt from the ball joint
    • Separate the ball joint from the control arm
    • Pry the ball joint out of the wheel knuckle with a pry bar
    • Remove the castle nut from the ball joint
    • Pull the ball joint out of the wheel knuckle
  3. step : Installing the Ball Joint (6:42)
    • Remove the cotter pin and castle nut from the new ball joint
    • Clean any grease from the wheel knuckle
    • Slide the ball joint into the wheel knuckle
    • Start the castle nut onto the ball joint by hand
    • Slide the ball joint studs into the control arm
    • Start the two 19mm nuts onto the ball joint studs by hand
    • Start the 17mm bolt into the control arm
    • Tighten the castle nut with a 19mm wrench
    • Line up the castle nut with the cotter pin hole
    • Insert the cotter pin into its hole
    • Fold over the cotter pin with pliers
    • Tighten the 17mm bolt
    • Tighten the two 19mm nuts to 55 foot-pounds of torque
  4. step : Installing the Wheel (9:32)
    • Slide the wheel onto the hub
    • Start the lug nuts with the tapered side facing the wheel
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts to 76 foot-pounds in a star pattern
    • Line up the hub cap with the valve stem
    • Push the hub cap onto the wheel
    • Pump the brake pedal until it feels firm

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Rubber Mallet
  • Sledge Hammer
  • Center Punch
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Cloth Rags

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Dead Blow Hammer

  • Wrenches - Metric

  • 19mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1985-1988 Chevy Nova Front Outer Tie Rod Pair
  • 1998-2002 Chevy Prizm Front Outer Tie Rod Pair
  • 1989-1997 Geo Prizm Front Outer Tie Rod Pair
  • 1990-1991 Lexus ES250 Front Outer Tie Rod Pair
  • 2004-2006 Scion xA Front Outer Tie Rod Pair
  • 2004-2006 Scion xB Front Outer Tie Rod Pair
  • 1987-1991 Toyota Camry Front Outer Tie Rod Pair
  • 1986-1999 Toyota Celica Front Outer Tie Rod Pair
  • 1986-1989 Toyota Celica Front Outer Tie Rod Pair
  • 1990-1993 Toyota Celica Front Outer Tie Rod Pair
  • 1985-1988 Toyota Corolla Front Outer Tie Rod Front Wheel Drive Pair
  • 1989-2002 Toyota Corolla Front Outer Tie Rod Pair
  • 2003-2005 Toyota Echo Front Outer Tie Rod Pair for Models with Power Steering
  • 1996-2000 Toyota Rav4 Front Outer Tie Rod Pair

This part replaces:

  • OE # 4504619175
  • OE # 4504629305 x2
  • Moog ES2382
  • OE # 4504629305
Part #: 1ASFK00290

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(11:14 min)