These outer tie rod ends are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) OUTER
  • Replaces dealer part numbers: 26100286, 26100287
  • Direct replacements
  • Built to strict quality control standards

NOTE: For 2002 Models, there were two different tie rod options available: 1st design (14mm thread) & 2nd design (16mm thread). These tie rods are correct for models with the 2nd design tie rods.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:43)
    • Pry off the hub cap with a flat blade screwdriver
    • Loosen the 35mm hub nut with the vehicle on the ground
    • Loosen the lug nuts
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:08)
    • Spray both ends of the outer tie rod with penetrating oil
    • Measure from the either end of the outer tie rod
    • Place a 26mm wrench on the larger nut
    • Place a 22mm wrench on the smaller nut
    • Break the 22mm nut free
    • Straighten the cotter pin with pliers and pull it through
    • Remove the nut with a 21mm socket from the wheel knuckle
    • Hit the wheel knuckle with a hammer
    • Twist off the outer tie rod
    • Remove the 22mm nut off the outer tie rod
  3. step : Installing the New Outer Tie Rod (3:08)
    • Mark where the 22mm nut was located on the old tie rod to the new tie rod
    • Screw on the nut
    • Twist the outer tie rod into place
    • Push the outer tie rod into the wheel knuckle
    • Measure and check the outer tie rod distance
    • Tighten the 21mm nut on the wheel knuckle
    • Insert and twist the cotter pin with a pair of pliers
    • Tighten the two nuts on the outer tie rod
  4. step : Reattaching the Wheel (4:33)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the hub nut to 103 ft/lbs
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Measuring Tape
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 26mm Wrench
  • 22mm Wrench
  • 10mm Wrench

4.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
1
0
0
Tie rod
I recently purchased this product from 1A Auto. It was very reasonably priced, and fit the vehicle as expected. I highly recommend 1A Auto to anyone who asks. Additionally, the how-to videos are top rate.
June 6, 2017
Purchased
11 months ago
Let time be the judge
It's just as important to write a review on parts for both fit and longevity.
These parts fit perfectly.
Tomorrow I will run the GMC and check my steering, I may need alignment.
And most importantly will be a review a year or two down the line to see how these parts are holding up.
Thanks,
Steve
Plymouth, MA 02360
August 29, 2017
Purchased
6 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(05:20 min)

Tools List:

    General Tools

  • Floor Jack
  • Measuring Tape
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 26mm Wrench
  • 22mm Wrench
  • 10mm Wrench



This part replaces:

  • Moog ES3675
  • Moog ES3676
  • OE # 26100286
  • OE # 26100286,26100287
  • OE # 26100287

Vehicle Fit

  • 2004-2007 Buick Rainier Front Outer Tie Rod Pair
  • 2003-2006 Chevy SSR Front Outer Tie Rod Pair
  • 2002 Chevy Trailblazer Tie Rod for Models with 16mm Thread Tie Rods Pair Front Outer
  • 2003-2009 Chevy Trailblazer Front Outer Tie Rod Pair
  • 2003-2005 Chevy Trailblazer EXT Front Outer Tie Rod Pair
  • 2002 GMC Envoy Tie Rod for Models with 16mm Thread Tie Rods Pair Front Outer
  • 2003-2009 GMC Envoy Front Outer Tie Rod Pair
  • 2003-2006 GMC Envoy XL Front Outer Tie Rod Pair
  • 2004-2005 GMC Envoy XUV Front Outer Tie Rod Pair
  • 2003-2008 Isuzu Ascender Front Outer Tie Rod Pair
  • 2002 Olds Bravada Tie Rod for Models with 16mm Thread Tie Rods Pair Front Outer
  • 2003-2004 Olds Bravada Front Outer Tie Rod Pair
  • 2005-2009 Saab 9-7X Front Outer Tie Rod Pair
Part #: 1ASFK00251

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More