Specifications:

  • Brand New Motorcraft Tie Rods
  • Comes as ap Pair
    • Fits LH (Driver Side) & RH (Passenger Side) Front Outer
  • Connect to inner tie rods
  • Built to strict quality control standards

Part Details

  • Location: Outer
  • Front or Rear Location: Front
  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. step : Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. step : Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. step : Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. step : Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. step : Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1998-2005 Ford Explorer Front Outer Tie Rod Pair Motorcraft MEOE79
  • 1998-2011 Ford Ranger Front Outer Tie Rod Pair Motorcraft MEOE79
  • 2001-2003 Mazda B2300 Truck Front Outer Tie Rod Pair Motorcraft MEOE79
  • 1998-2001 Mazda B2500 Truck Front Outer Tie Rod Pair Motorcraft MEOE79
  • 1998-2004 Mazda B3000 Truck Front Outer Tie Rod Pair Motorcraft MEOE79
  • 1998-2004 Mazda B4000 Truck Front Outer Tie Rod Pair Motorcraft MEOE79
  • 1998-2005 Mercury Mountaineer Front Outer Tie Rod Pair Motorcraft MEOE79

This part replaces:

  • Motorcraft MEOE79
  • OE # 5L5Z3A130AA
  • OE # F87Z3A130BA
Only 1 left in stock
Part #: MCSFK00005

MOTORCRAFT
Brand #: MEOE79

How-to Video:

(13:53 min)