MOOG EV80702 [INNER TIE ROD END]

This Moog brand inner tie rod end is just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) INNER
  • Replaces one of many dealer part numbers including: 68028831AB
  • Connects to center relay rod
  • Direct replacement
  • Built to strict quality control standards

When installed correctly and an alignment performed, this inner tie rod could also reduce uneven tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:52)
    • Loosen the lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:20)
    • Soak the tie rod jam nut and the other tie rod nut in rust penetrant
    • Loosen the jam nut with a 24mm wrench
    • Remove the 21mm nut from the outer tie rod
    • Strike the wheel spindle with a hammer to release the outer tie rod
    • Pull the tie rod down out of the wheel spindle
    • Twist off the tie rod, counting how many turns it takes to remove
    • Hold the inner tie rod with locking pliers
    • Mark the jam nut position with a marker
    • Twist off the jam nut with a 24mm wrench, counting how many turns it takes to remove
  3. step : Removing the Inner Tie Rod Boot (4:05)
    • Remove the two tie rod boot clamps with side cutters
    • Pull the boot off the inner tie rod
  4. step : Removing the Inner Tie Rod (4:50)
    • Twist the inner tie rod off the steering rack with a pipe wrench
  5. step : Installing the Inner Tie Rod (8:41)
    • Remove the travel limiter form the old inner tie rod
    • Put the travel limiter onto the new inner tie rod
    • Twist the inner tie rod onto the steering rack by hand
    • Tighten the inner tie rod with the pipe wrench
    • Remove the new jam nut from the inner tie rod
  6. step : Installing the Inner Tie Rod Boot (9:24)
    • Put the boot clamp on the steering rack side of the inner tie rod
    • Slide the boot onto the tie rod
    • Tighten the boot clamp
    • Pinch the wheel side boot clamp together with pliers
    • Slide the clamp onto the boot
    • Tighten the boot clamp
  7. step : Installing the Outer Tie Rod (10:36)
    • Mark the new jam nut
    • Twist on the new jam nut the same number of turns it took to remove the old one
    • Twist on the outer tie rod the same number of turns it took to remove the old one
    • Insert the outer tie rod stud into the wheel spindle
    • Fasten the 22mm nut onto the outer tie rod
    • Tighten the 22mm nut to 63 foot-pounds of torque
    • Tighten the new jam nut with a 22mm wrench
    • Grease the tie rod fitting until the boot swells
  8. step : Installing the Wheel (12:14)
    • Lift the wheel into place
    • Start the lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Safety Glasses
  • Gloves
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Pipe Wrench
  • Vise Grip Pliers
  • Side Cutters
  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Wrenches - Metric

  • 24mm Wrench
  • 21mm wrench
  • 22mm Wrench
  • 20mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2010 Chrysler 300 Front Inner Tie Rod Rear Wheel Drive MOOG EV80702
  • 2008-2010 Dodge Challenger Front Inner Tie Rod MOOG EV80702
  • 2006-2010 Dodge Charger Front Inner Tie Rod Rear Wheel Drive MOOG EV80702
  • 2005-2008 Dodge Magnum Front Inner Tie Rod Rear Wheel Drive MOOG EV80702

This part replaces:

  • MOOG EV80702
  • OE # 68028831AB
Part #: 1ASTE00045

Out of Stock

MOOG
Brand #: EV80702

How-to Video:

(12:42 min)