MOOG ES3571 [FRONT OUTER TIE ROD END PAIR]

These Moog brand front outer tie rod ends are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) OUTER
  • Replaces one of many dealer part numbers including: 5098996AA, 52013468AB, 52013468AC, 52106710AA, 52106710AB, 52106710AC
  • Connect to inner tie rods
  • Direct replacements
  • Built to strict quality control standards

When installed correctly and an alignment performed, these outer tie rods could also reduce uneven tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:47)
    • Loosen the lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:14)
    • Soak the tie rod jam nut and the other tie rod nut in rust penetrant
    • Loosen the jam nut with a 24mm wrench
    • Remove the 21mm nut from the outer tie rod
    • Strike the wheel spindle with a hammer to release the outer tie rod
    • Pull the tie rod down out of the wheel spindle
    • Twist off the tie rod, counting how many turns it takes to remove
    • Hold the inner tie rod with locking pliers
    • Mark the jam nut position with a marker
    • Twist off the jam nut with a 24mm wrench, counting how many turns it takes to remove
  3. step : Installing the Outer Tie Rod (5:25)
    • Mark the new jam nut
    • Twist on the new jam nut the same number of turns it took to remove the old one
    • Twist on the outer tie rod the same number of turns it took to remove the old one
    • Insert the outer tie rod stud into the wheel spindle
    • Fasten the 22mm nut onto the outer tie rod
    • Tighten the 22mm nut to 63 foot-pounds of torque
    • Tighten the new jam nut with a 22mm wrench
    • Grease the tie rod fitting until the boot swells
  4. step : Installing the Wheel (7:04)
    • Lift the wheel into place
    • Start the lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Gloves
  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Side Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • Complete Metric Socket Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2010 Chrysler 300 Outer Tie Rod Pair Rear Wheel Drive MOOG ES3571
  • 2008-2010 Dodge Challenger Pair Tie Rod Outer MOOG ES3571
  • 2006-2010 Dodge Charger Rear Wheel Drive Pair Tie Rod Outer MOOG ES3571
  • 2000-2004 Dodge Dakota Pair Tie Rod Outer 2 Wheel Drive MOOG ES3571
  • 2005-2010 Dodge Dakota Pair Tie Rod Outer MOOG ES3571
  • 2000-2003 Dodge Durango Pair Tie Rod Outer 2 Wheel Drive MOOG ES3571
  • 2005-2008 Dodge Magnum Rear Wheel Drive Pair Tie Rod Outer MOOG ES3571
  • 2006-2009 Mitsubishi Raider Pair Tie Rod Outer MOOG ES3571

This part replaces:

  • MOOG ES3571
Part #: MGSFK00028

Out of Stock

MOOG
Brand #: ES3571

How-to Video:

(07:32 min)